Abstract:The Moving Particle Semi-implicit-Controlled Volume (MPS-CV) method, based on the MPS method and Finite Volume Method (FVM), is a particle-grid coupling method. In this method, the particle interaction models in the MPS method are used to discretize and solve the momentum equation. For the eutectic reaction model, the FVM is used to solve the mass transfer equation if the particle locates at the boundary or the interface between different substances. In contrast, the particle interaction models are still used to discretize and solve the remaining particles' mass transfer equations. Therefore, it has advantages in describing fluid interfaces with large deformation and phase transition problems. Simultaneously, the MPS-CV method avoids the apparent error in calculating the mass transfer equation of boundary and interface between different substances due to the truncation of support domain in that area particles while using particle interaction models in the MPS method. In this study, the simulation of one-dimensional mass transfer and phase transition was used to verify the MPS-CV method, and the results were compared with those obtained by the MPS method. It showed that the MPS-CV method could get more accurate results in the calculation than the MPS method. Then the cladding oxidation mechanism at 1300 - 1800 K and the dissolution behavior between ZrO2 and molten zirconium at 2373 - 2573 K were analyzed using the MPS-CV method. The results indicated that the change of oxygen content obeyed parabolic laws. So did the oxide and alpha-Zr(O) layers' growth rates in cladding oxidation. And compared with the fixed parabolic relations used in commercial codes, the MPS-CV method can obtain the corresponding relationships according to different reaction conditions. The dissolution between ZrO2 and molten zirconium at high temperatures showed a parabolic pattern in the early stage. In the later stage of the reaction, the oxygen in the melt gradually reached saturation, and the solid ZrO2 did not continue to melt. The simulation results of the molten zirconium with the same volume but different contact areas with ZrO2 crucible showed that the larger the contact area was, the higher the growth rate of oxygen content in the melting the early stage of the reaction was. And it also showed that the larger the contact area was, the less dissolution volume of the ZrO2 crucible was.

Modeling of Zircaloy Oxidation Through Dynamic Mesh Deformation

Modeling of oxidation of structural materials in LBE systems

Constriction Percolation Model for Coupled Diffusion-Reaction Corrosion of Zirconium in PWR

Improved cellular automata modeling of corrosion/oxidation mechanism of stainless steel in LBE

Development of oxidation model for zirconium alloy cladding and application in the analysis of cladding behavior under loss of coolant accident

Specific Aspects of Internal Corrosion of Nuclear Clad Made of Zircaloy

Long-Term Oxidation of Zirconium Alloy in Simulated Nuclear Reactor Primary Coolant—Experiments and Modeling

3D reconstruction and interconnectivity quantification of the nano-porosity in the oxide layer of corroded Zr alloys

Development of an oxidation model for the prediction of the corrosion risk induced by deposits on cladding surface in PWRs

Numerical Investigation of Oxidation and Dissolution Behavior in the Fuel Cladding Using MPS-CV Method

Mechanical–chemical coupling phase-field modeling for inhomogeneous oxidation of zirconium induced by stress–oxidation interaction

Numerical Investigation of Ballooning and Burst for Chromium Coated Zircaloy Cladding

Studies of Electrochemical Oxidation of Zircaloy Nuclear Reactor Fuel Cladding Using Time-Of-Flight-Energy Elastic Recoil Detection Analysis

CRUD deposition induced multi-physics effects analysis in PWR

Phase-Field Modeling of Thermally-Grown Oxide and Damage Evolution in Environmental Barrier Coatings

Simulation of nuclear fuel clad high-temperature ballooning under loss-of-coolant accident conditions considering anisotropic creep

Numerical Modeling and Simulation of the Solid Oxide Cell Stacks and Metal Interconnect Oxidation with OpenFOAM

Zircaloy Plate Rolling Simulation with an Effective Strain-Rate-Dependent Stress-Updating Algorithm

Model development for oxidation and degradation behavior of accident tolerant Cr coating on Zr alloy cladding under high temperature steam atmosphere

Role of zirconium conversion coating in corrosion performance of aluminum alloys: An integrated first-principles and multiphysics modeling approach

Coupled Modeling and Simulation of Phase Transformation in Zircaloy-4 Fuel Cladding Under Loss-of-Coolant Accident Conditions