Mid-surface scaling invariance of some bending strain measures

Amit Acharya

2024-04-04

Abstract:The mid-surface scaling invariance of bending strain measures proposed in [Acharya (2000)] is discussed in light of the work of [

Analysis of PDEs,Soft Condensed Matter

What problem does this paper attempt to address?

Mid-Surface Scaling Invariance of Some Bending Strain Measures

Amit Acharya

DOI: https://doi.org/10.1007/s10659-024-10066-9

2024-04-03

Journal of Elasticity

Abstract:Abstract The mid-surface scaling invariance of bending strain measures proposed in (Int. J. Solids Struct. 37(39):5517–5528, 2000) is discussed in light of the work of (J. Elast. 146(1):83–141, 2021).

materials science, multidisciplinary,mechanics,engineering
Degenerate Scales And Boundary Element Analysis Of Two Dimensional Potential And Elasticity Problems

Wen-jun He,Hao-jiang Ding,Hai-chang Hu

DOI: https://doi.org/10.1016/0045-7949(95)00343-6

IF: 5.372

1996-01-01

Computers & Structures

Abstract:Some widely used conventional boundary integral equations yield non-equivalent solutions compared to their corresponding boundary value problems when the scales in the fundamental solutions reach their degenerate scale values. The effects of such degenerate scales on a two-dimensional boundary element solution of potential and plane elasticity problems are investigated for different geometries. Moreover, a simple convenient method is suggested to evaluate these degenerate scales. On the other hand, using the necessary and sufficient boundary integral formulation can eliminate the non-equivalence of these conventional boundary integral formulations. Copyright (C) 1996 Elsevier Science Ltd
Assorted remarks on bending measures and energies for plates and shells, and their invariance properties

J. A. Hanna,E. Vitral

2024-10-10

Abstract:In this note, we address several issues, including some raised in recent works and commentary, related to bending measures and energies for plates and shells, and certain of their invariance properties. We discuss overlaps and distinctions in results arising from two different definitions of stretching, correct an error and citation oversights in our prior work, reiterate some of the early history of dilation-invariant bending measures, and provide additional brief observations regarding the relative size of energetic terms and the symmetrization of bending measures. A particular point of emphasis is the distinction between dilation-invariant measures and a recently introduced non-dilation-invariant measure for shells and curved rods. In the course of this discussion, we provide a simpler presentation of the elementary, but much neglected, fact that the through-thickness derivative of tangential stretch of material near the mid-surface of a thin body is the product of the mid-surface stretch and change in curvature.

Soft Condensed Matter
Diffraction-Based Multiscale Residual Strain Measurements

Namit Pai,Sanjay Manda,Bhargav Sudhalkar,Bethany Syphus,David Fullwood,René de Kloe,Stuart Wright,Anirban Patra,Indradev Samajdar

DOI: https://doi.org/10.1093/mam/ozae011

IF: 4.0991

2024-03-07

Microscopy and Microanalysis

Abstract:Modern analytical tools, from microfocus X-ray diffraction (XRD) to electron microscopy-based microtexture measurements, offer exciting possibilities of diffraction-based multiscale residual strain measurements. The different techniques differ in scale and resolution, but may also yield significantly different strain values. This study, for example, clearly established that high-resolution electron backscattered diffraction (HR-EBSD) and high-resolution transmission Kikuchi diffraction (HR-TKD) [sensitive to changes in interplanar angle (Δθθ)], provide quantitatively higher residual strains than micro-Laue XRD and transmission electron microscope (TEM) based precession electron diffraction (PED) [sensitive to changes in interplanar spacing (Δdd)]. Even after correcting key known factors affecting the accuracy of HR-EBSD strain measurements, a scaling factor of ∼1.57 (between HR-EBSD and micro-Laue) emerged. We have then conducted "virtual" experiments by systematically deforming an ideal lattice by either changing an interplanar angle (α) or a lattice parameter (a). The patterns were kinematically and dynamically simulated, and corresponding strains were measured by HR-EBSD. These strains showed consistently higher values for lattice(s) distorted by α, than those altered by a. The differences in strain measurements were further emphasized by mapping identical location with HR-TKD and TEM-PED. These measurements exhibited different spatial resolution, but when scaled (with ∼1.57) provided similar lattice distortions numerically.

materials science, multidisciplinary,microscopy
Scaling of the elastic energy of small balls for maps between manifolds with different curvature tensors

Milan Krömer,Stefan Müller

DOI: https://doi.org/10.48550/arXiv.2103.15387

2022-12-10

Abstract:Motivated by experiments and formal asymptotic expansions in the physics literature, Maor and Shachar (J. Elasticity 134 (2019), 149-173) studied the behaviour of a model elastic energy of maps between manifolds with incompatible metrics. For thin objects they analysed the scaling of the minimal elastic energy as a function of the thickness. In particular they showed that for maps from a ball of radius h in an oriented Riemannian manifold to Euclidean space, the infimum of a model elastic energy per unit volume scales like the fourth power of h and after rescaling one gets convergence to a quadratic expression in the curvature tensor R(p), where p denotes the centre of the ball. In this paper we show the same result for general compact oriented Riemannian targets with R(p) replaced by a suitable difference of the curvature tensors in the target and the domain, thus answering Open Question 1 in the paper by Maor and Shachar. The result extends noncompact targets provided they satisfy a uniform regularity condition. A key idea in the proof is to use Lipschitz approximations to define a suitable notion of convergence.

Analysis of PDEs
Effect of shape imperfections on elastic stresses of U-bends subjected to in-plane moment

L.A. Krishna,A.R. Veerappan,S. Shanmugam

DOI: https://doi.org/10.1108/ijsi-01-2020-0012

2020-06-30

International Journal of Structural Integrity

Abstract:Purpose Precise assessment of elastic stress is required in the field of fracture mechanics. While bending a straight pipe, the deformation of the circular cross section out of roundness called ovality and thinning are foreseeable. The ovality has a significant effect on the structural integrity of the pipe. The sole objective of this paper is to provide new analytical solutions to predict accurate elastic stress distribution at the median section of the U-bend, with deformities such as ovality and thinning when subjected to in-plane closing moment by using elastic finite element analysis. Design/methodology/approach The quarter model of the U bend has been analysed by using ABAQUS. The elastic stress components included in this analysis are longitudinal bending stress, longitudinal membrane stress, circumferential bending stress and circumferential membrane stress. Based on finite element results, analytical elastic stress solutions are also provided for both longitudinal and circumferential stresses by using these stress components. Findings As the ovality has a significant effect, it is further included in the analytical solution. The thinning is not included since it has very little effect. Analytical stress solutions are provided for a wide range of bend characteristics to include ovality, mean radius and thickness. Originality/value Significance of ovality and thinning on elastic stress of U-bend has not been reported in the existing literature.
Non-affine bending mode of thin cylindrical tubes

Efi Efrati,Yifan Wang,Heinrich M. Jaeger,Thomas A. Witten

DOI: https://doi.org/10.48550/arXiv.1603.01808

2016-03-06

Abstract:We discuss the response of thin cylindrical tubes to small indentations. The stretching-free embedding of these surfaces is completely determined by the embedding of one edge curve, thus reducing their bending response to an effectively one dimensional problem. We obtain that in general thin cylindrical tubes will bend non-uniformly in response to an indentation normal to their surface. As a consequence, their local bending stiffness, as measured by indenting at various locations along their axis, is predicted to peak at the center and decrease by a universal factor of 4 at either end of the tube. This characteristic spatial profile of the bending stiffness variation allows a direct determination of the bending modulus of very thin tubes that are shorter than their pinch persistence length, $l_{p}\propto R^{3/2}/t^{1/2}$, where $R$ is the tube diameter and $t$ its wall thickness. We compare our results with experiments performed on rolled-up stainless steel sheets.

Soft Condensed Matter
Conformal Deformations of a Dilational Material Surface

Chen, Yi-chao,Fried, Eliot

DOI: https://doi.org/10.1007/s10659-023-10003-2

2023-03-11

Journal of Elasticity

Abstract:Dilational materials, for which the angles between pairs of material fibers are preserved under deformations, are an important class of metamaterials. Although these materials are typically made by assembling discrete elemental building blocks in repeating patterns, continuum mechanics provides a powerful tool for exploring their macroscopic properties and response. We present an analysis of the constraint, the constitutive relation, and the equilibrium equations for homogeneous and isotropic dilational elastic material surfaces. We also describe the possibility of penalizing deviations from local area preservation to yield a framework for approximating isometric deformations of unstretchable elastic material surfaces.

mechanics,materials science, multidisciplinary,engineering
Strain measurement by contour analysis

Georg C. Ganzenmüller,Puneeth Jakkula,Stefan Hiermaier

DOI: https://doi.org/10.48550/arXiv.2211.14030

2022-11-25

Abstract:Background: The determination of yield stress curves for ductile metals from uniaxial material tests is complicated by the presence of tri-axial stress states due to necking. A need exists for a straightforward solution to this problem. Objective: This work presents a simple solution for this problem specific to axis-symmetric specimens. Equivalent uniaxial true strain and true stress, corrected for triaxiality effects, are calculated without resorting to inverse analysis methods. Methods: A computer program is presented which takes shadow images from tensile tests, obtained in a backlight configuration. A single camera is sufficient as no stereoscopic effects need to be addressed. The specimen's contours are digitally extracted, and strain is calculated from the contour change. At the same time, stress triaxiality is computed using a novel curvature fitting algorithm. Results: The method is accurate as comparison with manufactured solutions obtained from Finite Element simulations show. Application to 303 stainless steel specimens at different levels of stress triaxiality show that equivalent uniaxial true stress -- true strain relations are accurately recovered. Conclusions: The here presented computer program solves a long-standing challenge in a straightforward manner. It is expected to be a useful tool for experimental strain analysis.

Materials Science
An essay on deformation measures in isotropic thin shell theories. Bending versus curvature

Ionel-Dumitrel Ghiba,Peter Lewintan,Adam Sky,Patrizio Neff

2023-12-19

Abstract:It has become commonplace for the stored energy function of any realistic shell model to align ``within first order" with the classical Koiter membrane-bending (flexural) shell model. In this paper, we assess whether certain extended Cosserat shell models are consistent with the classical linear Koiter model. In doing this, we observe that there are numerous reasons why a modified version of the classical Koiter model should be considered, a consensus reached not only by Koiter himself but also by Sanders and Budiansky, who independently developed the same theory during the same period. To provide a comprehensive overview of the strain measures employed in our Cosserat shell models, this paper presents them in a unified manner and compares them with the strain measures previously utilized in the literature. We show that all our new strain tensors either generalize (in the case of nonlinear constrained or unconstrained models) or coincide (in the case of the linear constrained model) with the strain tensors recognized as the ``best" or those possessing a well-defined geometric interpretation connected to bending or curvature.

Mathematical Physics
Infinitesimal conformal deformations of triangulated surfaces in space

Wai Yeung Lam,Ulrich Pinkall

DOI: https://doi.org/10.48550/arXiv.1702.04019

2018-04-18

Abstract:We study infinitesimal conformal deformations of a triangulated surface in Euclidean space and investigate the change in its extrinsic geometry. A deformation of vertices is conformal if it preserves length cross-ratios. On one hand, conformal deformations generalize deformations preserving edge lengths. On the other hand, there is a one-to-one correspondence between infinitesimal conformal deformations in space and infinitesimal isometric deformations of the stereographic image on the sphere. The space of infinitesimal conformal deformations can be parametrized in terms of the change in dihedral angles, which is closely related to the Schläfli formula.

Metric Geometry,Complex Variables,Differential Geometry
The non-uniform transformation strain problem for an anisotropic ellipsoidal inclusion

R.J. Asaro,D.M. Barnett

DOI: https://doi.org/10.1016/0022-5096(75)90012-5

IF: 5.582

1975-02-01

Journal of the Mechanics and Physics of Solids

Abstract:The problem of an anisotropic ellipsoidal inclusion which undergoes a stress-free transformation strain (in the sense of J.D. Eshelby) is considered, and the following theorem is proved: If an ellipsoidal region in an infinite anisotropic linear elastic medium undergoes, in the absence of its surroundings, a stress-free transformation strain which is a polynomial of degree M in the position coordinates xt, then the final stress and strain state in the transformed inclusion, when constrained by its surroundings, is also a polynomial of degree M in xt.

mechanics,materials science, multidisciplinary,physics, condensed matter
Anisotropic, non-uniform misfit strain in a thin film bonded on a plate substrate

Y. Huang,D. Ngo,X. Feng,A.J. Rosakis

DOI: https://doi.org/10.12989/imm.2008.1.1.123

2008-01-01

Interaction and multiscale mechanics

Abstract:Current methodologies used for the inference of thin film stresses through curvature measurements are strictly restricted to stress and curvature states which are assumed to remain uniform over the entire film/substrate system. These methodologies have recently been extended to non-uniform stress and curvature states for the thin film subject to non-uniform, isotropic misfit strains. In this paper we study the same thin film/substrate system but subject to non-uniform, anisotropic misfit strains. The film stresses and system curvatures are both obtained in terms of the non-uniform, anisotropic misfit strains. For arbitrarily non-uniform, anisotropic misfit strains, it is shown that a direct relation between film stresses and system curvatures cannot be established. However, such a relation exists for uniform or linear anisotropic misfit strains, or for the average film stresses and average system curvatures when the anisotropic misfit strains are arbitrarily non-uniform.
A new anisotropic bending model for nonlinear shells: Comparison with existing models and isogeometric finite element implementation

Eshwar J. Savitha,Roger A. Sauer

DOI: https://doi.org/10.1016/j.ijsolstr.2023.112169

2023-04-19

Abstract:A new nonlinear hyperelastic bending model for shells formulated directly in surface form is presented, and compared to four prominently used bending models. Through an essential set of elementary nonlinear bending test cases, the stresses and moments of each model are examined analytically. Only the proposed bending model passes all the test cases while the other bending models either fail or only pass the test cases for small deformations. The proposed new bending model can handle large deformations and initially curved surfaces. It is based on the principal curvatures and their directions in the initial configuration, and it thus can have different bending moduli along those directions. These characteristics make it flexible in modeling a given material, while it does not suffer from the pathologies of existing bending models. Further, the bending models are compared computationally through four classical benchmark examples and one contact example. As the underlying shell theory is based on Kirchhoff-Love kinematics, isogeometric NURBS shape functions are used to discretize the shell surface. The linearization and efficient finite element implementation of the proposed new model are also provided.

Computational Engineering, Finance, and Science
Bending of Biomimetic Scale Covered Beams Under Discrete Non-periodic Engagement

Hessein Ali,Hossein Ebrahimi,Ranajay Ghosh

DOI: https://doi.org/10.1016/j.ijsolstr.2019.01.021

2018-06-30

Abstract:Covering elastic substrates with stiff biomimetic scales significantly alters the bending behavior via scales engagement. This engagement is the dominant source of nonlinearity in small deflection regime. As deformation proceeds, an initially linear bending response gives way to progressive stiffening and thereafter a geometrically dictated 'locked' configuration. However, investigation of this system has been carried out until date using assumption of periodic engagement even after scales contact. This is true only under the most ideal loading conditions or if the scales are extremely dense akin to a continuum assumption on the scales. However, this is not true for a practical system where scales are more discrete and where loading can alter periodicity of engagement. We address this nonlinear problem for the first time in small deflection and rotation regime. Our combined modeling and numerical analysis show that relaxing periodicity better represents the geometry of discrete scales engagement and mechanics of the beam under general loading conditions and allows us to revisit the nonlinear behavior. We report significant differences from predictions of periodic models in terms of predicting the behavior of scales after engagement. These include the difference in the angular displacement of scales, normal force magnitudes along the length, moment curvature relationship as well as a distinct nature of the locking behavior. Therefore, non-periodicity is an important yet unexplored feature of this problem, which leads to insights, absent in previous investigations. This opens way for developing the structure-property-architecture framework for design and optimization of these topologically leveraged solids.

Soft Condensed Matter
Strain linearization for structural strain evaluation and maximum equivalent structural strain criterion

Yu Sun,Cheng-Hong Duan,Ming-Wan Lu

DOI: https://doi.org/10.1016/j.ijpvp.2016.09.001

IF: 2.56

2016-01-01

International Journal of Pressure Vessels and Piping

Abstract:This paper is focused on the gross plastic deformation design check of the direct route in European standard EN 13445-3 and its applications. Six methods for the evaluation of the structural strain are introduced and compared. A generally applicable method for structural strain evaluation – the strain linearization method is presented. Refer to the maximum principle structural strain criterion used by the direct route in EN 13445-3, a maximum equivalent structural strain criterion is presented, and the criterion is more suitable for ductile materials widely used in the pressure vessels.
Investigation on the invariance of fractal characteristics preserved under horizontal linear stretching

Binyan Yu,Yongshun Liang

DOI: https://doi.org/10.1142/s0219887824400292

2024-06-26

International Journal of Geometric Methods in Modern Physics

Abstract:International Journal of Geometric Methods in Modern Physics, Ahead of Print. In this paper, we mainly make research on whether fractal characteristics of an object with a fractal curve shape will keep invariable under being subjected to horizontal linear stretching. For two continuous functions [math] and [math], it has been proven that the graph of [math] has the same fractal dimensions with the graph of [math] when [math] is a linear function. Some examples have also been provided to corroborate our theoretical results. This work may contribute to the dimensional theory of fractal curves and have practical application significance in physics.

physics, mathematical
A finite-element discretization of some boundary value problems for nonlinear strain-limiting elastic bodies

Hyun C. Yoon,S. M. Mallikarjunaiah

DOI: https://doi.org/10.1177/10812865211020789

2021-06-08

Mathematics and Mechanics of Solids

Abstract:It is well known that the linearized theory of elasticity admits the logically inconsistent solution of singular strains when applied to certain naive models of fracture while the theory is a first-order approximation to finite elasticity in the asymptotic limit of infinitesimal displacement gradient. Meanwhile, the strain-limiting models, a special subclass of nonlinear implicit constitutive relations, predict uniformly bounded strain in the whole material body including at the strain-concentrator such as a crack tip or reentrant corner. Such a nonlinear approximation cannot be possible within the standard linearization procedure of either Cauchy or Green elasticity. In this work, we examine a finite-element discretization for several boundary value problems to study the state of stress–strain in the solid body of which response is described by a nonlinear strain-limiting theory of elasticity. The problems of notches, oriented cracks, and an interface crack in anti-plane shear are analyzed. The numerical results indicate that the linearized strain remains below a value that can be fixed a priori, therefore, ensuring the validity of the nonlinear model. In addition, we find high stress values in the neighborhood of the crack tip in every example, thereby suggesting that the crack tip acts as a singular energy sink for a stationary crack. We also calculate the stress intensity factor (SIF) in this study. The computed value of SIF in the nonlinear strain-limiting model is corresponding to that of the classical linear model, and thereby providing a tenet for a possible local criterion for fracture. The framework of strain-limiting theories, within which the linearized strain bears a nonlinear relationship with the stress, can provide a rational basis for developing physically meaningful models to study a crack evolution in elastic solids.

mechanics,materials science, multidisciplinary,mathematics, interdisciplinary applications
Buckling and yield strength estimation of architected materials under arbitrary loads

Morten N. Andersen,Yiqiang Wang,Fengwen Wang,Ole Sigmund

DOI: https://doi.org/10.1016/j.ijsolstr.2022.111842

IF: 3.667

2022-11-01

International Journal of Solids and Structures

Abstract:Buckling strength estimation of architected materials has mainly been restricted to load cases oriented along symmetry axes. However, realistic load scenarios usually exhibit more general stress distributions. This study employs local member analyses to estimate the buckling strength surface of stretch-dominated lattice structures. As an integral part of the method, the yield strength surface is also determined. Local members are analyzed under different boundary conditions, i.e., simply-supported, clamped as well as rotational springs accounting for lattice topologies. The local member estimations are compared with accurate but expensive numerical linear microstructural buckling analyses for different loadings. The local member approach provides a valuable tool to quickly estimate the microstructural buckling strength of stretch-dominated lattice structures, especially for applications where the stress state is non-uniform such as infill in additive manufacturing. Using the local member approach, we compute the entire buckling strength surfaces of an orthotropic bulk modulus optimal plate, an isotropic stiffness optimal plate, and an isotropic truss lattice structure subjected to rotated uni-axial loads. All the considered lattice structures possess high buckling strength anisotropy. In addition, the isotropic stiffness optimal plate structure possesses a near-isotropic yield strength surface while the truss counterpart possesses an anisotropic one. Inspired by the buckling strength surface calculations, we further propose a new isotropic plate lattice configuration with enhanced buckling strength isotropy without stiffness or yield strength deterioration.

mechanics
The bending of thin strips with a non-uniform transverse curvature

Jason Shore,Andrew Viquerat,Guy Richardson,Guglielmo Aglietti

DOI: https://doi.org/10.1016/j.ijsolstr.2022.112026

IF: 3.667

2022-11-10

International Journal of Solids and Structures

Abstract:The non-linear flexural behaviour of a tape spring — whose cross section has a uniform curvature — is produced by the presence of an elastic instability. However, these are not the only structures that possess non-linear flexural behaviour. Panel-springs and bridged tape springs are examples of structures that can also produce this behaviour. Predicting the flexural behaviour of these structures is more challenging because their cross section is non-uniform. This work presents an analytical model that can predict the opposite-sense flexural behaviour of thin strips that have a non-uniform cross section. The novel attribute of this model is in the utilisation of a univariate polynomial series to describe the initial cross section of the strip. The model is applied to a range of bridged tape springs and panel-springs, with the results compared with solutions obtained from the Finite Element (FE) method. A consistent error of less than 5.5% is achieved between the analytical model and the FE model when the snap-through moment and propagation moment are compared. The analytical model is also compared with independent experimental data of the flexural behaviour of a traditional carpenter's tape measure. An error of less than 1% and 7% of the snap-through moment and propagation moment, respectively, is achieved.

mechanics

Mid-surface scaling invariance of some bending strain measures

Mid-Surface Scaling Invariance of Some Bending Strain Measures

Degenerate Scales And Boundary Element Analysis Of Two Dimensional Potential And Elasticity Problems

Assorted remarks on bending measures and energies for plates and shells, and their invariance properties

Diffraction-Based Multiscale Residual Strain Measurements

Scaling of the elastic energy of small balls for maps between manifolds with different curvature tensors

Effect of shape imperfections on elastic stresses of U-bends subjected to in-plane moment

Non-affine bending mode of thin cylindrical tubes

Conformal Deformations of a Dilational Material Surface

Strain measurement by contour analysis

An essay on deformation measures in isotropic thin shell theories. Bending versus curvature

Infinitesimal conformal deformations of triangulated surfaces in space

The non-uniform transformation strain problem for an anisotropic ellipsoidal inclusion

Anisotropic, non-uniform misfit strain in a thin film bonded on a plate substrate

A new anisotropic bending model for nonlinear shells: Comparison with existing models and isogeometric finite element implementation

Bending of Biomimetic Scale Covered Beams Under Discrete Non-periodic Engagement

Strain linearization for structural strain evaluation and maximum equivalent structural strain criterion

Investigation on the invariance of fractal characteristics preserved under horizontal linear stretching

A finite-element discretization of some boundary value problems for nonlinear strain-limiting elastic bodies

Buckling and yield strength estimation of architected materials under arbitrary loads

The bending of thin strips with a non-uniform transverse curvature