Abstract:In recent years, weight reduction of automobile bodies has been effective in reducing carbon dioxide emissions. For this reason, the replacement of steel, which has a large specific gravity, with aluminum alloys and carbon fiber reinforced plastics is being promoted for the right materials in the right places. In this case, an appropriate dissimilar material joining method is needed in terms of ease of assembly, joining performance, and cost. Friction stir welding (FSW) has emerged as a promising joining method for a variety of engineering applications. FSW is a solid-phase joining technique that has been shown to have significant advantages over conventional welding in terms of the strength and quality of the joints produced. However, during joining of metallic materials by FSW, microstructural changes may occur that affect their corrosion degradation. In this study, the corrosion behavior of A6061 jointed with high-strength steel (SPCC980) by FSW in aqueous NaCl solution and the effect of Al alloy microstructural changes on it were investigated. In this study, FSW was performed on A6061 and SPCC980 steel plates, and galvanic corrosion behavior was investigated by immersion tests and surface observations, as well as electrochemical measurements of Al alloys. Immersion tests were performed in 1 M NaCl solution. Micro electrochemical polarization tests of A6061 were also performed to investigate the corrosion behavior. In the immersion test of the galvanic couple of A6061 and SPCC980 steel plates in NaCl solution, galvanic corrosion occurred with the Al alloy as the anode and the steel plate as the cathode, and hydrogen evolution was observed mainly from the BM site on A6061 in the initial stage of immersion. This is due to the hydrogen evolution reaction occurring inside the pitting corrosion of the A6061. The pits was formed near Fe-rich inclusions in the BM site. In the HAZ site, corrosion propagated from Fe-rich inclusions along grain boundaries, but no pitting corrosion was formed. In the NZ site, minor localized corrosion was developed. These results indicate that the susceptibility to localized corrosion and its morphology differ in each site on the A6061. The difference in localized corrosion susceptibility on the A6061 was considered to be caused by the difference in the distribution of Fe-rich inclusions. However, the fact that the size and number of Fe-rich inclusions in each site did not differ suggests that the difference in anodic dissolution activity near Fe-rich inclusions affects pitting corrosion susceptibility in each site. A6061 alloy is a precipitation-strengthened Al alloy reinforced by β'' phase, which is a metastable phase of Mg 2 Si, and dense precipitation of β'' phase was observed in the BM site. Therefore, the reason for the higher localized corrosion susceptibility of BM is related to the precipitation of the β'' phase. This paper is based on results obtained from a project, JPNP14014, commissioned by the New Energy and Industrial Technology Development Organization (NEDO).

The Anti-corrosion Property of 6061 Aluminum Alloy Subjected to Direct Current Interference in Marine Environment

Study on the Corrosion Behavior and Mechanism of 6061 Aluminum Alloy under Alternating Current Interference in 3.5% NaCl Solution

An Investigation on Corrosion Behavior and Mechanism of CoCrFeNi HEA in NaCl Solution under Direct Current Interference

Corrosion Susceptibility of Passive Films on 1060, 2024, and 5083 Aluminum Alloys: Experimental Study and First-Principles Calculations

Effects of Na2S2O3 Concentration and Solution Temperature on Anti-corrosion Property of 6061 Aluminum Alloy in Marine Environment

Corrosion Behavior of Al Alloy A6061 Jointed with High-Tensile Strength Steel By Friction Stir Welding in NaCl Solution

Corrosion Behavior of 6061 Aluminum Alloy in Simulated SO2-Polluted Seawater

Corrosion Failure and Mechanical Property Degradation of Anodized 5a06 Aluminum Alloy in a Marine Environment

Passivation and Chloride-Induced Corrosion Behavior of Aluminum Alloys in Pore Solution of Portland Cement Paste

Research on Corrosion Resistance of Anodized and Sealed 6061 Aluminum Alloy in 3.5 % Sodium Chloride Solution

Investigation of Long-term Corrosion of AA2024 and AA5119 Aluminum Alloys under chromate coating in Marine Atmosphere by Electrochemical Impedance Technology

Effect of quenching treatment on corrosion behavior and mechanical properties of 6061 aluminum alloy

Inhibitive Effect of Seawater on the Corrosion of Particulate-Reinforced Aluminum-Matrix Composites and Monolithic Aluminum Alloy

Corrosion Evolution of High-Strength Aluminum Alloys in the Simulated Service Environment of Amphibious Aircraft in the Presence of Chloride and Bisulfite

Corrosion Behavior and Mechanical Performance of 7085 Aluminum Alloy in a Humid and Hot Marine Atmosphere

Corrosion Behavior of 5083 Al-alloy in Seawater and Its Cathodic Protection

Impact of Corrosion on the Degradation of the Mechanical Properties of 2195 and 2297 Al Alloys in the Marine Environment

Study on the Influence of Surface Treatment Process on the Corrosion Resistance of Aluminum Alloy Profile Coating

Corrosion Behavior of Aluminum Alloys in Different Alkaline Environments: Effect of Alloying Elements and Anodization Treatments

Localized Corrosion and Corrosion Inhibitor of Al-alloy AA6061 Beneath Electrolyte Layers

Corrosion Behavior of the 2024 Aluminum Alloy in the Atmospheric Environment of the South China Sea Islands