Abstract:Deep shale gas reservoirs, compared to shallow and intermediate shale gas reservoirs, usually exhibit lower fracture complexity, smaller stimulated volume, poorer conductivity, and faster production decline when the same injection scheme and construction parameters are used. As a result, specific injection scenarios for deep shale reservoirs must be investigated. In this paper, a series of laboratory fracturing tests were conducted to investigate the influence of injection scenarios on deep shale hydraulic fracture initiation and propagation. The black shale of the Lower Silurian Longmaxi formation in the Sichuan Basin was adopted, and four different injection schemes (constant fluid rate injection, cyclic injection, shut-in intermittent injection, and low-frequency pulse pressurization injection) were utilized in these experiments. The energy evolution during hydraulic fracturing with different injection schemes was analyzed by an array of acoustic emission (AE) sensors. Furthermore, the internal fracture geometry of the shale specimens after failure was determined using high-resolution CT scanning. Two parameters, fracture bulk density and fractal dimension were defined to quantitatively characterize the post-pressure fracture complexity. The results indicate that the rock breakdown pressure rises rapidly as the injection rate increases, for conventional monotonic rate injection. Although increasing the injection rate can serve the purpose of increasing the net pressure in the seam and enhancing the fracture complexity, it makes it easier to approach the equipment pressure limit. Unlike conventional hydraulic fracturing, which mainly induces tensile fractures near the wellbore, cyclic fracturing is more likely to cause fatigue damage to the rock, resulting in the formation of subcritical microcracks, which gradually grow into macroscale fractures. In addition, the cyclic injection method can reduce the rock breakdown pressure by approximately 24% compared with the conventional continuous injection method. The shut-in intermittent injection method can also reduce the breakdown pressure of shale by 22%, but this method is not conducive to enhancing the fracture complexity. Pulse fracturing creates the most complex fracture morphology among the four injection schemes tested. The rapid changes in wellbore pressure over a short time can easily result in the formation of multiple fractures around the borehole. Our experimental results and theoretical analysis can provide theoretical support for the optimization of injection schemes for deep shale hydraulic fracturing.

Hydraulic fracturing behaviors of shale under coupled stress and temperature conditions simulating different burial depths

Study on rock mechanics characteristics of deep shale in Luzhou block and the influence on reservoir fracturing

Experimental Study on Mechanical, Brittleness, and Fracture Behavior of Deep Shales Subjected to Fracturing Fluid-Shale Interactions at Reservoir Temperature and In-Situ Stress Conditions

Investigating fracture initiation and propagation in deep buried shale due to thermal shock: a numerical approach

Study on the influence of thermo-pressure coupling environment on the fracture properties of shale in deep reservoirs

Study on fracture propagation behavior of deep high-temperature shale gas based on the modified MERR criterion

Elasticity and Characteristic Stress Thresholds of Shale under Deep In Situ Geological Conditions

Shale brittleness evaluation under high temperature and high confining stress based on energy evolution

Mixed-mode fracture behavior in deep shale reservoirs under different loading rates and temperatures

Numerical simulation on hydraulic fracture propagation in laminated shale based on thermo-hydro-mechanical-damage coupling model

Pore-Scale Simulation of Fracture Propagation by CO2 Flow Induced in Deep Shale Based on Hydro-Mechanical Coupled Model

Combined Effect of In Situ Stress Level and Bedding Anisotropy on Hydraulic Fracture Vertical Growth in Deep Marine Shale Revealed via CT Scans and Acoustic Emission

Numerical simulation of hydraulic fracture propagation after thermal shock in shale reservoir

Comparative investigation of in situ hydraulic fracturing and high-temperature steam fracturing tests for meter-scale oil shale

Multiple hydraulic fracture propagation simulation in deep shale gas reservoir considering thermal effects

Experimental and numerical study on dynamic mechanical behaviors of shale under true triaxial compression at high strain rate

The Statistical Damage Constitutive Model of Longmaxi Shale under High Temperature and High Pressure

Experimental study of hydraulic fracture initiation and propagation in deep shale with different injection methods

An Experimental Investigation of the Thermophysical Properties of Shale Reservoirs: A Case Study of the Wufeng-Longmaxi Formation in the Jiaoshiba Area

Experimental study of hydraulic fracturing initiation and propagation from perforated wellbore in oil shale formation