Abstract:Drag reduction at the external surface of a cylinder in turbulent flows along the axial direction by circumferential wall motion is studied by direct numerical simulations. The circumferential wall oscillation can lead to drag reduction due to the formation of a Stokes layer, but it may also result in centrifugal instability, which can enhance turbulence and increase drag. In the present work, the Reynolds number based on the reference friction velocity and the nominal thickness of the boundary layer is 272. A map describing the relationship between the drag-reduction rate and the control parameters, namely, the angular frequency $\unicode[STIX]{x1D714}^{+}=\unicode[STIX]{x1D714}\unicode[STIX]{x1D708}/u_{\unicode[STIX]{x1D70F}0}^{2}$ and the streamwise wavenumber $k_{x}^{+}=k_{x}\unicode[STIX]{x1D708}/u_{\unicode[STIX]{x1D70F}0}$ , is obtained at the oscillation amplitude of ${A^{+}=A/u}_{\unicode[STIX]{x1D70F}0}=16$ , where $u_{\unicode[STIX]{x1D70F}0}$ is the friction velocity of the uncontrolled flow and $\unicode[STIX]{x1D708}$ is the kinematic viscosity of the fluid. The maximum drag-reduction rate and the maximum drag-increase rate are both approximately 48 %, which are respectively attained at $(\unicode[STIX]{x1D714}^{+},k_{x}^{+})=$ (0.0126, 0.0148) and (0.0246, 0.0018). The drag-reduction rate can be scaled well with the help of the effective thickness of the Stokes layer. The drag increase is observed in a narrow triangular region in the frequency–wavenumber plane. The vortices induced by the centrifugal instability become the primary coherent structure in the near-wall region, and they are closely correlated with the high skin friction. In these drag-increase cases, the effective control frequency or wavenumber is crucial in scaling the drag-increase rate. As the wall curvature normalised by the boundary layer thickness becomes larger, the drag-increase region in the $(\unicode[STIX]{x1D714}^{+},k_{x}^{+})$ plane as well as the maximum drag-increase rate also become larger. Net energy saving with a considerable drag-reduction rate is possible when reducing the oscillation amplitude. At $A^{+}=4$ , a net energy saving of 18 % can be achieved with a drag-reduction rate of 25 % if only the power dissipation due to viscous stress is taken into account in an ideal actuation system.

Acceleration is the Key to Drag Reduction in Turbulent Flow

An energy-efficient pathway to turbulent drag reduction

Drag Reduction Via Turbulent Boundary Layer Flow Control

Experimental research on drag reduction by polymer additives in a turbulent pipe flow

Drag Reduction in Turbulent Flows along a Cylinder by Streamwise-Travelling Waves of Circumferential Wall Velocity

Dynamics of propagating turbulent pipe flow structures. Part I: Effect of drag reduction by spanwise wall oscillation

Drag Reduction by Spanwise Wall Oscillation in Wall-Bounded Turbulent Flows

Drag reduction induced by superhydrophobic surfaces in turbulent pipe flow

A review of turbulent skin-friction drag reduction by near-wall transverse forcing

Location and scales of drag reduction in turbulent pipe flow with wall oscillations at low Reynolds number

Numerical Investigation of Microbubble Drag Reduction on an Axisymmetric Body Based on Eulerian Multiphase Model

Rational Analysis of Drag Reduction Variation Induced by Surface Microstructures Inspired by the Middle Section of Barchan Dunes at High Flow Velocity

Drag-Reducing Flows in Laminar-Turbulent Transition Region

Direct numerical simulation of drag reduction in rotating pipe flow up to

Drag Reduction by Laminar Flow Control

Drag reduction in turbulent Taylor–Couette flow by axial oscillation of inner cylinder

Turbulent drag reduction by spanwise wall forcing. Part 2. High-Reynolds-number experiments

On-off pumping for drag reduction in a turbulent channel flow

Laminarising turbulent pipe flow by linear and nonlinear optimisation

Numerical Analysis of the Drag Reduction for Turbulent Pulsating Pipe Flows Based on Large Eddy Simulations

Drag reduction study of naturally occurring oscillating axial flow induced by helical corrugated surface in Taylor Couette flow