Abstract:To enhance the toughness of metallic glasses (MGs), considerable scientific efforts have been made to investigate the physical mechanism of fracture behavior of MGs in past few years. However, many unresolved puzzles remain about the fracture mechanisms of MGs at present. In this paper, Molecular Dynamics (MD) simulations have been used to investigate the tensile fracture behavior of Al based MGs under nine different Engineering strain rates. Our results show that the higher the Engineering strain rate is, the longer the period of plastic deformation, the shorter the crack length. we have observed that Al amorphous with notch gradually crystallizes during tensile fracture, however, there are differences in the degree of crystallization and atomic arrangement as well as micro-structure in different regions with different Engineering strain rates. In the process of tensile fracture of Al based MGs, the crack propagation mainly along the hexagonal-close-packed (HCP) grain boundaries between face-centered-cubic (FCC) crystal blocks. As the Engineering strain increases, numerous HCP atoms located at grain boundaries gradually migrate into the interior of FCC crystal blocks, the velocity of crack propagation will also increase and finally induce the brittle fracture of Al based MGs. Meanwhile, we effectively demonstrated the existence of HCP and FCC atoms in Al based MGs during tensile deformation by analyzing the bond-orientational order parameters q l . The analysis of thermodynamics (entropy) showed that there is a positive correlation between the Engineering strain rate and the strain of maximum entropy when the Engineering strain rate exceeds 0.002 ps -1 . The formation of cavitation ahead of crack could be attributed to the migrate of atoms from the higher entropy cavity region to the lower entropy crystallization region. This study enriches the traditional tensile deformation theories and provides a new understanding for the physical origins of cavitation in the crack tip of MGs.

Influence of Matrix Composition on Microstructural Yielding and Vickers Hardness in Phase Separated Glasses

Role of elastic deformation in determining the mixed alkaline earth effect of hardness in silicate glasses

Effect of Crystalline Phase on Deformation Behaviors of Amorphous Matrix in a Metallic Glass Composite

Notable Internal Thermal Effect On The Yielding Of Metallic Glasses

Microstructural evolution and analysis of Zr–Co/Cu–Al glassy composites and crystallized alloys via indentation and MD simulations

Tuning the hardness and crack resistance through liquid–liquid phase separation in an aluminosilicate glass

An Atomistic Investigation of Structural Evolution in Metallic Glass Matrix Composites

Influence of chemical composition on the room temperature plas-ticity of C15 Ca-Al-Mg Laves phases

The Competing Effect of Initial Crack Depth Versus Chemical Strengthening Parameters on Apparent Fracture Toughness of Sodium Aluminosilicate Glass

Evolution of the Primary Crystals and the Amorphous Matrix Following Annealing of a Bulk Zr56.6Cu17.3Ni12.5Al9.6Ti4 Metallic Glass

Microstructure evolution and mechanical properties of Cu46Zr47Al7 bulk metallic glass composite containing CuZr crystallizing phases

Microstructure and Crystallization Behavior of Glasses in the ZrO2-ZnO-Al2O3-SiO2 System

Effect of Thermo-Mechanical Histories on the Microstructure and Properties of Zr65Al10Ni10Cu15 Metallic Glassy Plates

The Effect of Primary Crystallizing Phases on Mechanical Properties of Cu46zr47al7 Bulk Metallic Glass Composites

Dynamics, Structure and Glass Formation of Calcium Aluminate Liquids

Mechanical properties of metallic glass matrix composites: Effects of reinforcement character and connectivity

EFFECT OF SPECIAL PHASE SEPARATION ON MICROSTRUCTURE AND PROPERTY OF GLASS-CERAMICS

Microstructure and mechanical properties of MgO–Al2O3–SiO2–TiO2 glass–ceramics

Deformation and Crystallization of a Zr41.2Ti13.8Cu12.5Ni10Be22.5 Bulk Metallic Glass in the Supercooled Liquid Region

Mechanically Driven Phase Separation and Corresponding Microhardness Change in Cu60Zr20Ti20 Bulk Metallic Glass

The influence of Engineering strain rates on the atomic structure, crack propagation and cavitation formation in Al based metallic glass