Abstract:Anisotropic two-dimensional layered materials with low-symmetric lattices have attracted increasing attention due to their unique orientation-dependent mechanical properties. Black arsenic (b-As), with the puckered structure, exhibits extreme in-plane anisotropy in optical, electrical and thermal properties. However, experimental research on mechanical properties of b-As is very rare, although theoretical calculations predicted the exotic elastic properties of b-As, such as anisotropic Young's modulus and negative Poisson's ratio. Herein, experimental observations on highly anisotropic elastic properties of b-As were demonstrated using our developed in situ tensile straining setup based on the effective microelectromechanical system. The cyclic and repeatable load-displacement curves proved that Young's modulus along zigzag direction was ~1.6 times greater than that along armchair direction, while the anisotropic ratio of ultimate strain reached ~2.5, attributed to hinge structure in armchair direction. This study could provide significant insights to design novel anisotropic materials and explore their potential applications in nanomechanics and nanodevices.

What problem does this paper attempt to address?

The problem that this paper attempts to solve is to explore the highly anisotropic elastic properties of two - dimensional black arsenic (b - As) in different directions. Although theoretical calculations predict that black arsenic has unique elastic properties, such as anisotropic Young's modulus and negative Poisson's ratio, experimental research on its mechanical properties is very limited. Therefore, this paper conducts a systematic experimental study on two - dimensional black arsenic under a scanning electron microscope (SEM) by developing an in - situ tensile testing device based on micro - electro - mechanical systems (MEMS) to verify its highly anisotropic elastic properties. Specifically, the researchers solved this problem through the following methods: 1. **Sample preparation**: Use the PDMS - assisted exfoliation method to obtain clean, uniform, and large - area black arsenic flakes from natural minerals, and determine the lattice orientation by polarized Raman spectroscopy. Subsequently, use the focused ion beam (FIB) technology to cut the selected black arsenic flakes into nanoribbons, ensuring that they are arranged in a specific direction (zigzag direction or armchair direction). 2. **In - situ tensile test**: Transfer the prepared black arsenic nanoribbons to the MEMS device, and use Pt deposition to fix both ends to ensure that no slip occurs during the tensile process. Apply tensile force through the MEMS device, record the load - displacement curve, and observe the elastic deformation and fracture process of the nanoribbons. 3. **Data analysis**: Analyze the load - displacement curve to calculate the Young's modulus and maximum strain of black arsenic in different directions. The results show that the Young's modulus in the zigzag direction is approximately 40.8 GPa, which is 1.6 times that in the armchair direction (approximately 25.8 GPa). In addition, the maximum strain in the armchair direction is approximately 8.9%, which is 2.5 times that in the zigzag direction (approximately 3.5%). These experimental results not only verify the theoretical predictions but also provide important insights for the design of new anisotropic materials and their applications in nanomechanics and nano - devices.

Experimental observation of highly anisotropic elastic properties of two-dimensional black arsenic

Experimental Observation of Highly Anisotropic Elastic Properties of Two-Dimensional Black Arsenic

Highly Anisotropic Elastic Properties of Suspended Black Arsenic Nanoribbons

Suspended Black Arsenic Nanoribbons with Anisotropic Elastic Properties for Nanomechanical Devices

Black Arsenic: A Layered Semiconductor with Extreme in-plane Anisotropy

Intralayer Negative Poisson's Ratio in Two-Dimensional Black Arsenic by Strain Engineering

In-Plane Optical and Electrical Anisotropy of 2D Black Arsenic

Ultra-high mechanical stretchability and controllable topological phase transitions in two-dimensional arsenic

Raman Spectra and Strain Effects in Bismuth Oxychalcogenides

Anisotropic mechanical properties of monolayer fullerene network: An interplay between two types of interfullerene bonds

Electronic structures and optical properties of arsenene and antimonene under strain and an electric field

Anisotropic mechanics of two‐dimensional materials

Thermodynamic Origins of Structural Metastability in Two-Dimensional Black Arsenic

Mechanical Anisotropy in Two-Dimensional Selenium Atomic Layers

Extra‐High Mechanical and Phononic Anisotropy in Black Phosphorus Blisters (Small 45/2023)

Direct Observation of Crystalline Distortions in Mechanically Exfoliated Low-symmetric 2D Materials

Mechanical and Electrical Anisotropy of Few-Layer Black Phosphorus

Mechanics and Mechanically Tunable Band Gap in Single-Layer Hexagonal Boron-Nitride

Extra‐High Mechanical and Phononic Anisotropy in Black Phosphorus Blisters

Effects of short-range order and interfacial interactions on the electronic structure of two-dimensional antimony-arsenic alloys

Remarkable Anisotropic Phonon Response in Uniaxially Strained Few-Layer Black Phosphorus