Abstract:A TD-split basal texture with two peaks highly tilted from the normal direction (ND) towards the transverse direction (TD) is usually developed in Mg-Zn-Ca plates and can effectively improve ductility and formability. In the present study, the texture evolution during cold rolling and subsequent annealing of a Mg-2Zn-1Ca plate with initial TD-split texture was investigated, and new insights into the mechanisms of texture evolution were obtained. The results show that a dumbbell-shaped basal texture transformed into an elliptical shape after 41% cold rolling. The random distribution of prismatic planes became preferred with largely parallel to the rolling direction (RD). Crystal plasticity simulations revealed that basal slip was the predominant deformation mode, and inclined basal poles toward the ND. The activation of other non-basal slips would retard this tendency. Prismatic slip with a relative activity of 20% to 30% preserved the pre-existing TD-split texture after a high rolling reduction of 41%. Pyramidal slip prevented the formation of basal fiber and lead to a spreading of basal poles toward the RD mainly at strains over 29%. After full recrystallization, the elliptical TD-split basal texture became a dumbbell-shaped TD-split texture. Grain nucleation was observed at grain boundaries (GBN mechanism), within deformation twins (DTN mechanism), and near precipitates (PSN mechanism). GBN and DTN mainly developed a TD-split basal-texture. Instead of the formation of random orientations as considered previously, PSN produced a TD-split basal-texture, and the basal poles exhibited a much wider distribution with high angle of the peaks off the ND. The grains nucleated by GBN, DTN, and PSN did not exhibit preferred growth, and consequently, the texture hardly changed during subsequent grain growth.

The effect of initial texture on multiple necking formation in polycrystalline thin rings subjected to dynamic expansion

Effect of Stress State on Plastic Behavior, Deformation Mechanism and Texture Evolution of an Mg-Gd-Y Alloy: Experiment and Multi-Scale Simulation

Crystal Plasticity Modeling and Neutron Diffraction Measurements of a Magnesium AZ31B Plate: Effects of Plastic Anisotropy and Surrounding Grains

Effects of texture and twinning on the torsional behavior of magnesium alloy solid rod: A crystal plasticity approach in comparison with uniaxial tension/compression

Effects of Highly-Textured and Untextured Polycrystalline Layers on Deformation Mechanisms in Amorphous Submicron-Layered Materials

Modeling the Micromechanical Behaviors of Zircaloy-2 Alloy under Large Deformation

Modeling of Texture Development during Metal Forming Using Finite Element Visco-Plastic Self-Consistent Model

Strain Rate and Anisotropic Effects on Incipient Plastic Deformation of Zn–Cu–Ti Alloy Sheets

The inhomogeneity of plastic deformation in ductile single crystals

Neck development in metal/elastomer bilayers under dynamic stretchings

Effect of uniaxial loading direction on mechanical responses and texture evolution in cold pilgered Zircaloy-4 tube: Experiments and modeling

Interaction between ductile damage and texture evolution in finite polycrystalline elastoplasticity

Numerical Simulation on Sheet Metal Forming with Rate-Independent Polycrystalline Plasticity Fem

Microstructure and Texture Optimization by Static Recrystallization Originating from {10-12} Extension Twins in a Mg-Gd-Y Alloy

Grain size dependent microstructure and texture evolution during dynamic deformation of nanocrystalline face-centered cubic materials

Combining crystal plasticity and phase field model for predicting texture evolution and the influence of nuclei clustering on recrystallization path kinetics in Ti-alloys

On the role of selective nucleation and growth to recrystallization texture development in a Mg-Gd-Zn alloy

Effect of Thermomechanical Processing on Microstructure and Mechanical Properties of CoCrFeNiMn High Entropy Alloy

Dynamic Recrystallization, Texture Evolution, and Improved Mechanical Properties of Mg-Y-Zn-V Alloy during Forging and Subsequent Extruding Deformation

Size Effect on Cyclic Torsion of Micro-Polycrystalline Copper Considering Geometrically Necessary Dislocation and Strain Gradient

Understanding the mechanisms of texture evolution in an Mg-2Zn-1Ca alloy during cold rolling and annealing