Abstract:Utilization of low-grade heat has attracted considerable attention as an inspiring pathway towards sustainable and low-carbon energy future. However. low-grade heat, either in the form of natural source or waste heat, is abundantly available but not yet effectively exploited. With the outstanding merits of free maintenance and high reliability, thermoacoustic engine is conceived as one of cost-effective and reliable alternative technologies for low-grade heat recovery. Most recently, two-phase thermoacoustic engine induced increasing interest, thanks to its capability of running across a small temperature difference between heat source and heat sink. In this work. a vapor-liquid phase-change thermoacoustic engine, where the working fluid undergoes periodic condensation and evaporation, is constructed to realize low temperature-differential operation. The engine consists of a looped thermoacoustic unit and a branch resonator, where the former contains a cold heat exchanger. a regenerator. a hot heat exchanger and segments of tubes, while the latter contains a gas reservoir and a load tube. R134a is adopted as the working fluid in the preliminary study of this thermoacoustic engine, for its boling point near ambient temperature at the operating pressure around 0.5 MPa. Besides, R1234ze(E) is also used as the working fluid. thanks to its zero ozone depletion potential and low global warming potential. The experiments focus on onset temperature and pressure ratio, since the former determines the lowest grade of usable heat source, while the latter is an essential parameter for evaluating the intensity of pressure oscillation. The results show that an onset temperature of 18.1 degrees C. lowest ever reported, can be achieved with R134a as working fluid when the regenerator is packed with copper mesh screens. The highest pressure ratio of 1.094 is achieved with R1234ze(E) as working fluid at a hot temperature of 183 degrees C and a heating power of 200 W. which is comparable to the single-stage looped travelling wave thermoacoustic engine with helium of 1 MPa as working fluid at a similar hot temperature but a much lower heating power. Besides, the onset temperature firstly drops and then rises with the decreasing mesh number of regenerator's mesh screen, while the pressure ratio always rises. It is also found that regenerator material has marked effect on the engine performance. The engine with copper mesh screen achieves the lowest onset temperature, then stainless steel, and finally nylon. Besides, the cases of pressure ratio are in the increasing order of nylon_ stainless steel and copper. The low temperature-differential onset enables the phase-change thermoacoustic engine to harvest the near roomtemperature heat source. Further work on performance optimization of this novel thermoacoustic engine is still necessary and will be our near future work.

Convective meta-thermal concentration for ultrahigh efficient Stirling engine with waste heat and cold utilization

Thermal Metamaterial for Convergent Transfer of Conductive Heat with High Efficiency

Working Mechanism and Characteristics of Gas Parcels in the Stirling Cycle

A Vapor-Liquid Phase-Change Thermoacoustic Engine Driven by Near Room-Temperature Heat Source

Experimental Investigations on Dynamic Performance of Organic Rankine Cycle Integrated with Latent Thermal Energy Storage under Transient Engine Conditions

Using Supercritical Heat Recovery Process in Stirling Engines for High Thermal Efficiency

Evaluation of heat transfer enhancement effect at the hot/cold end of a Stirling engine using performance improvement factor

Cool Down Time Optimization of the Stirling Cooler

Design Optimization with Computational Fluid Dynamic Analysis of Β-Type Stirling Engine

Performance analysis and multi-objective optimization based on a modified irreversible Stirling cycle

Optimization of solar-powered Stirling heat engine with finite-time thermodynamics

Experimental Investigation on Heat Transfer and Combustion of a Stirling Engine Combustor Fueled by Reformed Gas and Diesel Fuel

Theoretical analysis of a direct-coupled Stirling combined cooling and power system for heat recovery

Experimental and numerical study on a heat-driven direct-coupled Stirling refrigerator

Thermochemical Recuperation for Stirling Engines by Diesel Steam Reforming: Thermodynamic Analysis

Numerical Analysis on a Four-Stage Looped Thermoacoustic Stirling Power Generator for Low Temperature Waste Heat

Dynamic and thermodynamic characterization of a resonance tube-coupled free-piston Stirling engine-based combined cooling and power system

Constructal Design of Biogas Fired Stirling Engine-Based Micro Combined Heat and Power System Using a Novel Polytropic Endothermic/exothermic Thermal Model

Heat transfer characteristics of enhanced cooling tube with a helical wire under oscillatory flow in Stirling engine

Performance Analysis of Heat Pipe Micro-Reactor with Stirling Engine Based on Full-Scope Multi-Physics Coupled Simulation

Computer-aided molecular design of CO2-based mixture working fluid harvesting engine waste heat