Abstract:This paper reviews the history, the present status and possible future developments of photovoltaic (PV) materials for terrestrial applications. After a brief history and introduction of the photovoltaic effect theoretical requirements for the optimal performance of materials for pn-junction solar cells are discussed. Most important are efficiency, long-term stability and, not to be neglected, lowest possible cost. Today the market is dominated by crystalline silicon in its multicrystalline and monocrystalline form. The physical and technical limitations of this material are discussed. Although crystalline silicon is not the optimal material from a solid state physics point of view it dominates the market and will continue to do this for the next 5–10 years. Because of its importance a considerable part of this review deals with materials aspects of crystalline silicon. For reasons of cost only multicrystalline silicon and monocrystalline Czochralski (Cz) crystals are used in practical cells. Light induced instability in this Cz-material has recently been investigated and ways to eliminate this effect have been devised. For future large scale production of crystalline silicon solar cells development of a special solar grade silicon appears necessary. Ribbon growth is a possibility to avoid the costly sawing process. A very vivid R&D area is thin-film crystalline silicon (about 5–30μm active layer thickness) which would avoid the crystal growing and sawing processes. The problems arising for this material are: assuring adequate light absorption, assuring good crystal quality and purity of the films, and finding a substrate that fulfills all requirements. Three approaches have emerged: high-temperature, low-temperature and transfer technique. Genuine thin-film materials are characterized by a direct band structure which gives them very high light absorption. Therefore, these materials have a thickness of only one micron or less. The oldest such material is amorphous silicon which is the second most important material today. It is mainly used in consumer products but is on the verge to also penetrate the power market. Other strong contenders are chalcogenides like copper indium diselenide (CIS) and cadmium telluride. The interest has expanded from CuInSe2, to CuGaSe2, CuInS2 and their multinary alloys Cu(In,Ga)(S,Se)2. The two deposition techniques are either separate deposition of the components followed by annealing on one hand or coevaporation. Laboratory efficiencies for small area devices are approaching 19% and large area modules have reached 12%. Pilot production of CIS-modules has started in the US and Germany. Cadmium telluride solar cells also offer great promise. They have only slightly lower efficiency and are also at the start of production. In the future other materials and concepts can be expected to come into play. Some of these are: dye sensitized cells, organic solar cells and various concentrating systems including III/V-tandem cells. Theoretical materials that have not yet been realized are Auger generation material and intermediate metallic band material.

Glassy materials for Silicon-based solar panels: present and future

Mechanically Robust and Self-Cleaning Antireflective Coatings for Photovoltaic Modules

Towards long term sustainability of c-Si solar panels: The environmental benefits of glass sheet recovery

Perspectives of New Alternative Materials to Silicon for the Production of Photovoltaic Solar Cells

Overview of the Current State of Flexible Solar Panels and Photovoltaic Materials

Glass and Coatings on Glass for Solar Applications

Improving the Solar Cell Module Performance by a Uniform Porous Antireflection Layer on Low Iron Solar Glass

2.3% Efficiency Gains for Silicon Solar Modules Using a Durable Broadband Anti-reflection Coating

Reducing parasitic absorption and recombination losses in silicon solar cells through transition metal doped glass frit

Theoretic Guide for Using Photonic Glasses as Colored Covers for Solar Energy Harvesting

Photovoltaic materials, history, status and outlook

Glass/glass photovoltaic module reliability and degradation: a review

High-Efficiency, Mass-Producible, and Colored Solar Photovoltaics Enabled by Self-Assembled Photonic Glass

New Coating Paradigm to Boost Performance and Durability of Solar Receivers

Advancements in Photovoltaic Cell Materials: Silicon, Organic, and Perovskite Solar Cells

Using Photonic Glasses as Colored Covers for Solar Energy Harvesting

A state-of-the-art review on the multifunctional self-cleaning nanostructured coatings for PV panels, CSP mirrors and related solar devices

Anti-Reflection and Self-Cleaning Nanocoating to Improve the Performance of Flat Plate Solar Collector

Large-area smart glass and integrated photovoltaics

Soiling, cleaning, and abrasion: The results of the 5-year photovoltaic glass coating field study

A Selective Review of Ceramic, Glass and Glass-Ceramic Protective Coatings: General Properties and Specific Characteristics for Solar Cell Applications