Abstract:The primary mirror of very large submillimeter-wave telescopes will necessarily be segmented into many separate mirror panels. These panels must be continuously co-phased to keep the telescope wavefront error less than a small fraction of a wavelength, to ten microns RMS (root mean square) or less. This performance must be maintained continuously across the full aperture of the telescope, in all pointing conditions, and in a variable thermal environment. A wavefront compensation segmented mirror sensing and control system, consisting of optical edge sensors, Wavefront Compensation Estimator/Controller Soft ware, and segment position actuators is proposed. Optical edge sensors are placed two per each segment-to-segment edge to continuously measure changes in segment state. Segment position actuators (three per segment) are used to move the panels. A computer control system uses the edge sensor measurements to estimate the state of all of the segments and to predict the wavefront error; segment actuator commands are computed that minimize the wavefront error. Translational or rotational motions of one segment relative to the other cause lateral displacement of the light beam, which is measured by the imaging sensor. For high accuracy, the collimator uses a shaped mask, such as one or more slits, so that the light beam forms a pattern on the sensor that permits sensing accuracy of better than 0.1 micron in two axes: in the z or local surface normal direction, and in the y direction parallel to the mirror surface and perpendicular to the beam direction. Using a co-aligned pair of sensors, with the location of the detector and collimated light source interchanged, four degrees of freedom can be sensed: transverse x and y displacements, as well as two bending angles (pitch and yaw). In this approach, each optical edge sensor head has a collimator and an imager, placing one sensor head on each side of a segment gap, with two parallel light beams crossing the gap. Two sets of optical edge sensors are used per segment-to-segment edge, separated by a finite distance along the segment edge, for four optical heads, each with an imager and a collimator. By orienting the beam direction of one edge sensor pair to be +45 away from the segment edge direction, and the other sensor pair to be oriented -45 away from the segment edge direction, all six degrees of freedom of relative motion between the segments can be measured with some redundancy. The software resides in a computer that receives each of the optical edge sensor signals, as well as telescope pointing commands. It feeds back the edge sensor signals to keep the primary mirror figure within specification. It uses a feed-forward control to compensate for global effects such as decollimation of the primary and secondary mirrors due to gravity sag as the telescope pointing changes to track science objects. Three segment position actuators will be provided per segment to enable controlled motions in the piston, tip, and tilt degrees of freedom. These actuators are driven by the software, providing the optical changes needed to keep the telescope phased.

Lateral constraint for thin glass shell: analysis of the requirements and conceptual design for a segmented active mirror

Kinematic Analysis and Model Fabrication of a Space Deployable Optical Baffle

Mirror actively deformed and regulated for applications in space: design and performance

Research on Active Control for Thermal Deformation of Precise Membrane Reflector With Boundary SMA Actuators

Thin glass shells for active optics for future space telescopes

Deployment Dynamics for Flexible Deployable Primary Mirror of Space Telescope with Paraboloidal and Laminated Structure by Using Absolute Node Coordinate Method

Membrane Space Telescope: Active Surface Control with Radiative Adaptive Optics

Experiments on Quasi-Static and Dynamic Control of a PVDF Laminated Membrane-Like Mirror

Contactless actuators and pyramid wavefront sensor, the SPLATT concept for space active optics: an overview of the project and the last laboratory results

Numerical and Experimental Investigation on Dynamics of Deployable Space Telescope Experiencing Deployment and Attitude Adjustment Motions Coupled with Laminated Composite Shell

Design and Test of Small Mirror Supports for Harsh Environments

Design, analysis of self-configurable modular adjustable latch lock for segmented space mirrors

A Support Structure for A Compliant Deformable Mirror

The Design Of Support Structure Of Mirror Subassembly Of Space Remote Sensor

Wavefront Compensation Segmented Mirror Sensing and Control

Active optics in astronomy - Freeform mirror for the MESSIER telescope proposal

An innovative concept for the AsteroidFinder/SSB focal plane assembly

Development of mirrors made of chemically tempered glass foils for future X-ray telescopes

Analysis of active optics correction for a large honeycomb mirror

A Review of Lightweight Design for Space Mirror Core Structure: Tradition and Future