Abstract:Inconel 718 has good fabricability, high strength at elevated temperatures, and high corrosion resistance and is widely deployed in many aerospace and other high-performance applications. With the molten pool's rapid solidification during laser powder bed fusion (LPBF), the resulting microstructures differ from those expected in equilibrium conditions. Residual stresses, microsegregation, anisotropy, undesirable phases, layered structure, and lower mechanical properties are the challenges that must be addressed before LPBF-ed Inconel 718 parts can be industrially implemented. Heat treatment of Inconel 718 after the LPBF process is widely discussed in the literature, and the proposed heat treatment processes do not address all the challenges mentioned above. For this reason, specific heat treatments should be designed to achieve desired mechanical properties. Four different high-temperature heat treatment procedures were developed and tested in recent work to study the effect of various heat treatment parameters on the type of precipitates, grain size, room and elevated temperature mechanical properties, and creep properties of LPBF-ed Inconel 718. Two heat treatment procedures were designed to study the effect of eliminating the stress relief cycle and increasing the soaking time of solution heat treatment at the same hot isostatic pressing (HIP) and aging conditions. The other two heat treatment procedures were designed to study the effect of stress relief and aging parameters, with similar HIP and solution annealing parameters. The investigated heat treatment procedures showed the formation of equiaxed grain size and a significant amount of γ ′′ particles at the grain boundary in addition to primary carbide types (MC). Three different grain sizes could be obtained, starting with the same as-built microstructure by controlling post-process heat treatment parameters. The first type, coarse grain size (ASTM grain size No. G 3), suitable for creep application, was achieved by increasing the soaking time at the aging cycle. The second type, the formation of serrated grain boundaries suitable for good fatigue and creep properties, was achieved by decreasing the stress relief cycle's soaking time and temperature. The third type, fine grain size (ASTM grain size No. G 6), which is preferable for fatigue properties, was achieved by decreasing the soaking time at the solution annealing cycle. Among the different heat treatment conditions, the heat treatment with lower stress relief temperature and longer soaking time at solution annealing steps showed compromised equiaxed grain size with serrated grain boundaries, and it was selected for mechanical testing. The mechanical properties at room and elevated temperature (650 °C) and creep properties under constant axial stress of 690 MPa at 650 °C until failure were evaluated. The obtained elongation is > 2 × higher than the available properties in the AMS 5663 for wrought Inconel 718, AMS 5383 for cast Inconel 718, and ASTM F3055 for LPBF while maintaining a higher tensile strength above the average level found in the standards. It can be concluded that the performed heat treatment achieves higher mechanical properties. The values of UTS, YS, elongation, and reduction of area percentages are similar in the Z and XY orientations, revealing the presence of isotropic microstructure and uniform distribution of MC and γ ′′ precipitates.

Electrical Current-Assisted Low-Plasticity Burnishing of Inconel 718 Built by Laser Powder Bed Fusion: Surface Integrity and Fatigue Life Analysis

Optimization of electric current-assisted sustainable burnishing process of additively manufactured Inconel 718: trade-off between production rate and fatigue life

Effect of Surface Modification on the High Temperature Low Cycle Fatigue Performance of LPBF 316L Austenitic Steel

Surface Characteristics of Low Plasticity Burnished Laser Directed Energy Deposition Alloy IN718

Exploring the post-heat treatment on the electropolishing characteristics of laser powder bed fusion processed Inconel 718 superalloy

Laser shock peening as a post-processing technique for Inconel 718 components manufactured by laser powder bed fusion

Wire-EDM performance and surface integrity of Inconel 718 with unique microstructural features fabricated by laser powder bed fusion

Impact of annealing treatment on the fatigue behavior of Inconel 625 produced by laser‐based powder bed fusion

In-situ ultrasonic impact treatment (UIT) to improve the fatigue properties of laser powder bed fusion (LPBF) manufactured Inconel 718

An Experimentally Informed Computational Framework for Investigating the Role of Surface Roughness on High Cycle Fatigue Life of LPBF IN718

Microstructural, mechanical and wear behaviour of Inconel-718 produced through laser-powder bed-fused additive manufacturing

Optimization of the Post-Heat Treatment of Additively Manufactured IN718

A review on microstructure, mechanical behavior and post processing of additively manufactured Ni-based superalloys

Correlation between Surface Integrity and Low Cycle Fatigue Life of Machined Inconel 718

Influence of laser peening on the high-temperature fatigue life and fracture of Inconel 718 nickel-based alloy

Corrosion Properties and Passive Film Interface of Inconel 718 in NaNO3 Solution for Laser-Assisted Electrochemical Machining

A review of low plasticity burnishing and its applications

Improving surface quality and superficial microstructure of LDED Inconel 718 superalloy processed by hybrid laser polishing

Effects of Magnetic Abrasive Finishing on Microstructure and Mechanical Properties of Inconel 718 Processed by Laser Powder Bed Fusion

Effects of heat treatment on surface integrity and wear performance of Inconel 718 alloy fabricated by laser powder bed fusion process additive manufacturing under different laser power and scanning speed parameters

Effect of homogenization and solution treatments time on the elevated-temperature mechanical behavior of Inconel 718 fabricated by laser powder bed fusion