Abstract:Objectives: Due to the lack of literature concerning the selection of crown materials for the restoration of anterior teeth, this study aimed to investigate the effects of six distinct computer-aided design and computer-aided manufacturing (CAD-CAM) crown materials on stress and strain distribution within implant-supported maxillary central incisor restorations, employing finite element analysis (FEA). Furthermore, a comparative analysis was conducted between models that incorporated adjacent natural teeth and those that did not, intending to guide the selection of the most suitable modeling approach. Materials and methods: Crown materials, including Lava Ultimate, Enamic, Emax CAD, Suprinity, Celtra Duo, and Cercon xt ML, were the subjects of the investigation. FEA models incorporating Coulomb friction were developed. These models were subjected to an oblique load, simulating the average maximum bite force experienced by anterior teeth. The potential for failure in titanium implant components and the prosthesis crown was evaluated through von Mises and principal stress, respectively. Furthermore, the failure of crestal bone was assessed through principal strain values. Statistical analysis: Stress values for each implant component and strain values of the bone were extracted from the models. To assess the impact of the six groups of crown materials, Kruskal-Wallis analysis of variance and post-hoc comparisons were conducted. Additionally, a statistical comparison between the two groups with Lava Ultimate and Cercon xt ML was performed using the Mann-Whitney U test to determine the difference in the two modeling approaches. Results: Higher crown material stiffness led to decreased stress in the abutment, fixture, and retaining screw, along with reduced strain in the surrounding bone. However, the decrease in stress and strain values became less significant with increasing crown stiffness. Additionally, the model with adjacent teeth showed significantly lower stress and strain concentrations compared to the model without adjacent teeth. Conclusion: Crowns with a high elastic modulus were the optimal choice for anterior teeth restoration. Constructing FEA models with adjacent teeth was highly recommended to gain a deeper understanding of the mechanical behavior of dental implant restorations.

Biomechanical behavior of implant retained prostheses in the posterior maxilla using different materials: a finite element study

Biomechanical finite element analysis of short-implant-supported, 3-unit, fixed CAD/CAM prostheses in the posterior mandible

Effect of Different Framework Materials in Implant-Supported Fixed Mandibular Prostheses: A Finite Element Analysis

Stress analysis of different prosthesis materials in implant-supported fixed dental prosthesis using 3D finite element method

Biomechanical analysis comparing natural and alloplastic temporomandibular joint replacement using a finite element model

Implant-Supported Fixed Partial Prostheses With Different Prosthetic Materials: A Three-Dimensional Finite Element Stress Analysis

A 3D Finite Element Analysis Model of Single Implant-Supported Prosthesis under Dynamic Impact Loading for Evaluation of Stress in the Crown, Abutment and Cortical Bone Using Different Rehabilitation Materials

Biomechanical behavior of implants with prosthetic connection of the morse (Cone) type, with different angulations at the implant-abutment interface in multiple dental prostheses: a finite element study

Biomechanical investigation of maxillary implant-supported full-arch prostheses produced with different framework materials: a finite elements study

Effect of different implant configurations on biomechanical behavior of full-arch implant-supported mandibular monolithic zirconia fixed prostheses

Biomechanical Three-Dimensional Finite Element Analysis of Prostheses Retained With/without Zygoma Implants in Maxillectomy Patients.

A Patient Specific Biomechanical Analysis of Custom Root Analogue Implant Designs on Alveolar Bone Stress: A Finite Element Study

Effect of different biocompatible implant materials on the mechanical stability of dental implants under excessive oblique load

Biomechanical evaluation of anterior implants associated with titanium and zirconia abutments and monotype zirconia implants

A Three – Dimensional Finite Element Analysis of Polyetheretherketone PEEK in Dental Implant Prosthesis: A Novel Implant System

Finite Element Analysis of Anterior Implant-Supported Restorations with Different CAD-CAM Restorative Materials

Biomechanical analysis of different fixed dental restorations on short implants: a finite element study

Comparison of full‐arch mandibular reconstruction with dental implants using completely splinted or segmentally splinted prostheses with two different occlusal schemes: A finite‐element analysis

Biomechanical behavior of different designs of hybrid abutment-restoration on the posterior crown: a finite element analysis

Three-Dimensional Finite Element Analysis of Anterior Two-Unit Cantilever Resin-Bonded Fixed Dental Prostheses

A Biomechanical Evaluation of Distal Tilting Implants in All-on-Four Rehabilitation with Mild Mandibular Resorption: A Finite Element Analysis Study