Heart rate levels and ventricular ectopic activity during cardiac rehabilitation.

M. Simoons,C. Lap,J. Pool

DOI: https://doi.org/10.1016/0002-8703(80)90273-2

IF: 5.099

1980-07-01

American Heart Journal

Abstract:

What problem does this paper attempt to address?

Conch‐Shell‐Inspired Tough Ceramic

Meng Li,Nifang Zhao,Mengning Wang,Xuangeng Dai,Hao Bai

DOI: https://doi.org/10.1002/adfm.202205309

IF: 19

2022-01-01

Advanced Functional Materials

Abstract:Biological structural materials realize outstanding mechanical properties by assembling hard and soft components into complex hierarchical structures, which provide abundant inspirations for synthetic materials. Specifically, conch shell exhibits around ten times higher toughness than widely‐explored nacre due to its cross‐lamellar architecture at nano‐ to macroscopic scales. Previously, conch‐shell‐inspired materials are realized by 3D‐printing. However, it remains challenging to translate the properties of conch shell into synthetic materials because of the limited approaches to duplicating complex architecture with high ceramic contents. Here, a surface‐pattern‐induced ice‐templating strategy is reported to fabricate conch‐shell‐inspired composites with a cross‐lamellar structure across a 107‐fold range of length. This is realized by directional freezing on a grooved surface, which has previously been confirmed to induce preferential ice growth. These composites have a flexural strength of 165 MPa and a work of fracture of 8.2 kJ m–2, which are 2.5 and 2 times, respectively, higher than those of conch shell. Such conch‐shell‐inspired structure yields a toughness twice that of nacre‐mimetic structure due to multiple crack deflections. Additionally, the impact resistance of these composites is comparable to those of aluminum alloys. The research provides a feasible approach to fabricating bioinspired materials with complex architectures and multifunctionality.
Damage-Tolerance Strategies for Nacre Tablets

Shengnan Wang,Xinqiao Zhu,Qiyang Li,Rizhi Wang,Xiaoxiang Wang

DOI: https://doi.org/10.1016/j.jsb.2016.02.017

IF: 3.234

2016-01-01

Journal of Structural Biology

Abstract:Nacre, a natural armor, exhibits prominent penetration resistance against predatory attacks. Unraveling its hierarchical toughening mechanisms and damage-tolerance design strategies may provide significant inspiration for the pursuit of high-performance artificial armors. In this work, relationships between the structure and mechanical performance of nacre were investigated. The results show that other than their brick-and-mortar structure, individual nacre tablets significantly contribute to the damage localization of nacre. Affected by intracrystalline organics, the tablets exhibit a unique fracture behavior. The synergistic action of the nanoscale deformation mechanisms increases the energy dissipation efficiency of the tablets and contributes to the preservation of the structural and functional integrity of the shell.
Cost-effective Fabrication of Bio-Inspired Nacre-Like Composite Materials with High Strength and Toughness

Hongbo Wan,Nathanael Leung,Sana Algharaibeh,Tan Sui,Qiang Liu,Hua-Xin Peng,Bo Su

DOI: https://doi.org/10.1016/j.compositesb.2020.108414

IF: 11.322

2020-01-01

Composites Part B Engineering

Abstract:A cost-effective one-step densification process based on bi-directional freeze casting was investigated to produce nacre-like alumina/poly (methyl methacrylate) (PMMA) composites with a unique micro-layered (mu L) architecture. This method has the advantage of shorter processing time, as it requires only sintering once instead of twice as in the fabrication of conventional brick-and-mortar (BM) composites via freeze casting. By tuning the processing parameters, composites with different ceramic content and layer thickness were obtained. The resultant mechanical properties of mu L composites showed that ceramic content and wall thickness affected mechanical properties significantly. The mu L composite with fine ceramic walls (8 mu m) and relatively high ceramic fraction (72 vol%) exhibited an exceptional combination of high flexural strength (178 MPa) and fracture toughness (12.5 MPa m(1/2)). The mu L composites were also compared with the conventional BM composites. Although the fracture behaviour of both composites exhibited similar extrinsic toughening mechanisms, the composites with longer ceramic walls displayed superior mechanical properties in terms of strength and fracture toughness in comparison with the BM composites comprising short ceramic walls (i.e. bricks), due to the effectiveness of stress transfer of load-bearing ceramic phase within the composites.
Reinforcement mechanisms and optimum design of laminated ceramic composites

Xiaoqian Qian,Manzhen Ge,Yibing Wu,Hui Yang

IF: 1.292

1999-01-01

Journal of Inorganic Materials

Abstract:Laminated ceramic composites which have a unique structure, ha;ve been used in tailoring the microstrucure and mechanical properties of structural ceramics, and it is shown that both strength and toughness can be improved. In this paper, the different mechanisms that can be used to reinforce laminated ceramic composites were reviewed in two parts at macroscopic scale. Furthermore, optimum design of such composites was briefly painted out, and as an example, the fracture toughness was optimized by discussing the effects of changes in specimen variables, including lamina strength, interface bonding strength, as well as interface and lamina thickness in details.
Fabrication and Characterisation of Alumina/aluminium Composite Materials with a Nacre-Like Micro-Layered Architecture

Hongbo Wan,Nathanael Leung,Urangua Jargalsaikhan,Eric Ho,Chaolin Wang,Qiang Liu,Hua-Xin Peng,Bo Su,Tan Sui

DOI: https://doi.org/10.1016/j.matdes.2022.111190

IF: 9.417

2022-01-01

Materials & Design

Abstract:Many natural materials demonstrate ideal design inspirations for the development of lightweight composite materials with excellent damage tolerance. One notable example is the layered architecture of nacre, which possesses toughness an order of magnitude higher than its constituent parts. Man-made nacre-like ceramic/polymer composites obtained through direct infiltration of polymer in ceramic scaffolds have been shown to produce improved mechanical properties over other composite architectures. Replacing the polymer phase with metal could provide higher damage tolerance but the infiltration of metal into complex ceramic scaffolds is difficult due to the surface tension of molten metal. To address this, bioinspired nacre-like micro-layered (lL) alumina scaffolds with different ceramic fractions from 18 to 85% were infiltrated with aluminium alloy 5083 via pressureless and squeeze casting infiltrations techniques. The scaffolds were created using a bi-directional freeze-casting and one-step densification method. As a result, the lL alumina/aluminium composites displayed significant extrinsic toughening mechanisms with both high strength and toughness. The mechanical performance was highly dependent on the interface, microstructure, and composition. The nacre-like composites with 18% alumina and AlN interface displayed a maximum resistance-curve toughness up to around 70 MPa.m(1/2) (35 MPa.m(1/2) at the ASTM limit) and a flexural strength around 600 MPa. (C) 2022 The Author(s). Published by Elsevier Ltd.
High-Density 8Mb 1T-1C Ferroelectric Random Access Memory Embedded Within a Low-Power 130nm Logic Process

S. Summerfelt,Ted Moise,K. Udayakumar,K. Boku,K. Remack,John A. Rodriguez,J. Gertas,H. McAdams,S. Madan,J. Eliason,J. Groat,D. Kim,P. Staubs,M. Depner,R. Bailey

DOI: https://doi.org/10.1109/ISAF.2007.4393151

2007-05-27

Abstract:Ferroelectric memories are the most promising alternative to traditional embedded nonvolatile memories, such as flash and EEPROMs, because of their fast read/write cycle time, non-volatile data retention, low voltage/low power operation and low number of additional masks for fabrication (+2). An embedded ferroelectric memory (FRAM) has been developed using a 1.5 V, 130 nm 5 metal layer Cu/FSG logic process. The only modification to the logic process was the addition of a ferroelectric process module consisting of two additional masks (FECAP, VIAO) immediately before MET1. The ferroelectric was 70 nm Pb(Zr,Ti)O3 (PZT) deposited by metalorganic chemical vapor deposition (MOCVD). The electrical properties of a 8 Mb 1T-1C embedded FRAM were characterized. This eFRAM process has been used to simultaneously fabricate a digital signal processor (DSP) using the eFRAM process flow and the operating frequency is nearly the same relative to the CMOS baseline. This eFRAM process flow creates a technology platform that enables ultra-low-power devices.
Energy dissipation in composites with hybrid nacre-like helicoidal microstructures

Xin Ying Chan,Clarence Chua,Sharlene Tan,Hortense Le Ferrand

DOI: https://doi.org/10.1016/j.compositesb.2021.109608

2022-01-04

Abstract:Natural ceramic composites present complex microstructures that lead to tortuous crack paths and confer them high toughness. Current microreinforced composites do not yet reach the same level of complexity in their microstructures, resulting in poorer properties. To achieve complex microstructuration, magnetically-assisted slip casting (MASC) was conducted using a setup with 4 degrees of freedom. Among all possible microstructures, a hybrid design between nacre-like and helicoidal arrangements was selected due to its ability to tilt and twist the crack path. The hybrid microstructured specimen fabricated, consisting of aluminum oxide micro platelets in a silicone matrix, were tested under compression and their mechanical performance compared. Although nacre-like composites exhibited the highest strength and toughness, helicoidal hybrids could show some ductility and higher stiffness. The fabrication strategy proposed here could thus be a simple route to study more complex microstructures in view of increasing the toughness of microplatelet reinforced composites.

Materials Science
Printing nature: Unraveling the role of nacre's mineral bridges

Grace X Gu,Flavia Libonati,Susan D Wettermark,Markus J Buehler

DOI: https://doi.org/10.1016/j.jmbbm.2017.05.007

Abstract:Creating materials with strength and toughness has been a long-sought goal. Conventional engineering materials often face a trade-off between strength and toughness, prompting researchers seeking to overcome these limitations to explore more sophisticated materials, such as composites. This paradigm shift in material design is spurred by nature, which exhibits a plethora of heterogeneous materials that offer outstanding material properties, and many natural materials are widely regarded as examples of high-performing hybrid materials. A classic example is nacre, also known as mother-of-pearl, which boasts a combination of high stiffness, strength, and fracture toughness. Various microstructural features contribute to the toughness of nacre, including mineral bridges (MBs), nano-asperities, and waviness of the constituent platelets. Recent research in biomimicry suggests that MBs contribute to the high strength and toughness observed in nacre and nacre-inspired materials. However, previous work in this area did not allow for complete control over the length scale of the bridges and had limitations on the volume fraction of mineral content. In this work, we present a systematic investigation elucidating the effects of structural parameters, such as volume fraction of mineral phase and density of MBs, on the mechanical response of nacre-inspired additive manufactured composites. Our results demonstrate that it is possible to tune the composite properties by tuning sizes and content of structural features (e.g. MBs and mineral content) in a heterogeneous material. Looking forward, this systematic approach enables materials-by-design of complex architectures to tackle demanding engineering challenges in the future.
Biomimetic structure design — a possible approach to change the brittleness of ceramics in nature

Chang-an Wang,Yong Huang,Qingfeng Zan,Hai Guo,Shengyou Cai

DOI: https://doi.org/10.1016/S0928-4931(00)00133-8

2000-01-01

Abstract:Based on the analysis on structure of natural biomaterials, two kinds of ceramic composites with high toughness have been designed and prepared: one is fibrous monolithic Si3N4/BN composite imitating bamboos or trees in structure, the other is laminated Si3N4/BN composite imitating nacre in structure. Plastic forming methods, including extrusion and roll compaction, respectively, followed by hot-pressed sintering are used to prepare these two materials with particular structures. Both of the two composites have high values of fracture toughness and work of fracture: fracture toughness are 24 MPa m1/2 and 28 MPa m1/2, respectively, for fibrous monolithic and laminated Si3N4/BN composites, and works of fracture are both more than 4000 J/m2. The load-displacement curves reveal that these two materials with biomimetic structure exhibit non-brittle feature when applied load to fracture. Through analysis on fractographs of the materials, it is revealed that high toughness comes from the synergistic toughening among multi-level toughening mechanisms in different scales: weak interfaces, whiskers and elongated grains toughening in ceramic matrix cells.
Tough and Ductile Architected Nacre‐Like Cementitious Composites

Shashank Gupta,Hadi S. Esmaeeli,Reza Moini

DOI: https://doi.org/10.1002/adfm.202313516

IF: 19

2024-06-11

Advanced Functional Materials

Abstract:Tough Nacre‐like tabulated cementitious‐polymeric composites inspired by brick‐and‐mortar arrangement of mollusk shells are engineered using laser processing and lamination. Interlayer deformation, tortuous crack propagation guided by tabulated architecture, and crack bridging are the main toughening mechanisms, leading to rising resistance curves. Tablet sliding prevents tablet failure, enhancing fracture toughness and ductility by 17.1 and 19 folds, respectively. Enhancing fracture toughness and ductility of brittle materials such as concrete remains a challenge. Nature offers numerous mechanisms to enhance fracture toughness using purposeful designs of materials' architecture. Natural nacre exhibits high fracture toughness by promoting inelastic deformation and hierarchical toughening mechanisms. Here, "nacre‐like‐separated" and "nacre‐like‐grooved" cementitious composites inspired by brick‐and‐mortar arrangement of mollusk shells are proposed. These nacre‐like composites are engineered by laser processing cement paste into individual tablets and grooved patterns (as intentional defects) and laminating them with limited amounts of suitable elastomeric (polyvinyl siloxane) interlayers. It is found that interlayer deformation, tortuous crack propagation guided by the defects, and crack bridging are the main toughening mechanisms in these composites that lead to rising resistance curves. The study hypothesizes tablet sliding as an additional toughening mechanism in "nacre‐like‐separated", preventing tablet failure and leading to the postponed onset of bulk composite failure. These mechanisms significantly enhance both fracture toughness and ductility by 17.1 and 19 folds, compared to constituent hardened cement paste, respectively. By engineering laser‐induced defects into tabulated cementitious‐elastomeric material at meso‐scale, a class of tough and ductile cementitious composites is introduced, resulting in significantly high fracture toughness values (73.68 MPa.mm1/2), comparable to Ultra‐high‐performance‐concrete without sacrificing the strength.

materials science, multidisciplinary,nanoscience & nanotechnology,physics, applied,chemistry, physical, condensed matter
Tough, Bio-Inspired Hybrid Materials

E. Munch,M. E. Launey,D. H. Alsem,E. Saiz,A. P. Tomsia,R. O. Ritchie

DOI: https://doi.org/10.1126/science.1164865

IF: 56.9

2008-12-05

Science

Abstract:The notion of mimicking natural structures in the synthesis of new structural materials has generated enormous interest but has yielded few practical advances. Natural composites achieve strength and toughness through complex hierarchical designs that are extremely difficult to replicate synthetically. We emulate nature's toughening mechanisms by combining two ordinary compounds, aluminum oxide and polymethyl methacrylate, into ice-templated structures whose toughness can be more than 300 times (in energy terms) that of their constituents. The final product is a bulk hybrid ceramic-based material whose high yield strength and fracture toughness [∼200 megapascals (MPa) and ∼30 MPa·m 1/2 ] represent specific properties comparable to those of aluminum alloys. These model materials can be used to identify the key microstructural features that should guide the synthesis of bio-inspired ceramic-based composites with unique strength and toughness.

multidisciplinary sciences
Artificial Nacre with High Toughness Amplification Factor: Residual Stress‐Engineering Sparks Enhanced Extrinsic Toughening Mechanisms

Yu‐Feng Meng,Yin‐Bo Zhu,Li‐Chuan Zhou,Xiang‐Sen Meng,Yu‐Lu Yang,Ran Zhao,Jun Xia,Bo Yang,Yu‐Jie Lu,Heng‐An Wu,Li‐Bo Mao,Shu‐Hong Yu

DOI: https://doi.org/10.1002/adma.202108267

IF: 29.4

2022-01-21

Advanced Materials

Abstract:The high fracture toughness of mollusk nacre is predominantly attributed to the structure-associated extrinsic mechanisms such as platelet sliding and crack deflection. While the nacre-mimetic structures are widely adopted in artificial ceramics, the extrinsic mechanisms are often weakened by the relatively low tensile strength of the platelets with a large aspect ratio, which makes the fracture toughness of these materials much lower than expected. Here, it is demonstrated that the fracture toughness of artificial nacre materials with high inorganic contents can be improved by residual stress-induced platelet strengthening, which can catalyze more effective extrinsic toughening mechanisms that are specific to the nacre-mimetic structures. Thereby, while the absolute fracture toughness of the materials is not comparable with advanced ceramic-based composites, the toughness amplification factor of the material reaches 16.1 ± 1.1, outperforming the state-of-the-art biomimetic ceramics. The results reveal that, with the merit of nacre-mimetic structural designs, the overall fracture toughness of the artificial nacre can be improved by the platelet strengthening through extrinsic toughening mechanisms, although the intrinsic fracture toughness may decrease at platelet level due to the strengthening. It is anticipated that advanced structural ceramics with exceeding performance can be fabricated through these unconventional strategies.

materials science, multidisciplinary,chemistry, physical,physics, applied, condensed matter,nanoscience & nanotechnology
Tough and Ductile Architected Nacre‐Like Cementitious Composites (Adv. Funct. Mater. 39/2024)

Shashank Gupta,Hadi S. Esmaeeli,Reza Moini

DOI: https://doi.org/10.1002/adfm.202470230

IF: 19

2024-09-27

Advanced Functional Materials

Abstract:Nacre‐Like Cementitious Composites In article number 2313516, Reza Moini, Shashank Gupta, and Hadi S. Esmaeeli engineer tough Nacre‐like tabulated cementitious‐polymeric composites inspired by the brick‐and‐mortar arrangement of mollusk shells using laser processing and lamination. Interlayer deformation, tortuous crack propagation guided by tabulated architecture, and crack bridging are the main toughening mechanisms, leading to rising resistance curves. Tablet sliding prevents tablet failure, enhancing fracture toughness and ductility by 17.1 and 19 fold, respectively.

materials science, multidisciplinary,chemistry, physical,physics, applied, condensed matter,nanoscience & nanotechnology
Nacre-like carbon fiber-reinforced biomimetic ceramic composites: Fabrication, microstructure, and mechanical performance

Hailong Wu,Anfu Guo,Dekun Kong,Xunjin Li,Jingwen Wu,Hongbing Wang,Peng Qu,Shaoqing Wang,Shuai Guo,Chang Liu,Zhengyu Zhao,Jacob Grant Gallaspie,Yingbin Hu

DOI: https://doi.org/10.1016/j.ceramint.2024.04.270

IF: 5.532

2024-04-01

Ceramics International

Abstract:The unique structure of nacre is composed of 'bricks' and 'mortar,' which gives it excellent damage resistance. In this study, nacre-like bionic ceramic scaffolds were 3D-printed using vat photopolymerization (VPP) technology, filled with polymer, and reinforced with carbon fiber to create high-strength and high-toughness carbon fiber-reinforced bionic composites. This approach leverages additive manufacturing technology to easily overcome the challenges of fabricating complex bionic structures with a simple and flexible production process. It offers a practical method for developing other lightweight, high-strength, and tough bionic materials. The microstructure of the composites was observed using scanning electron microscopy and energy dispersive spectroscopy. Additionally, finite element method and molecular dynamics simulations were performed on the composites. The results indicate that the composite material increased the flexural strength by 293.52% and the fracture toughness by 109.36% compared to solid ceramic parts. The primary toughening mechanisms of carbon fiber include crack deflection, fiber "pull-out," and "debonding" within the composite.

materials science, ceramics
3D printing of layered ceramic/carbon fiber composite with improved toughness

Jinxing Sun,Shixiang Yu,James Wade-Zhu,Xiaoteng Chen,Jon Binner,Jiaming Bai

DOI: https://doi.org/10.1016/j.addma.2021.102543

IF: 11

2022-02-01

Additive Manufacturing

Abstract:Strong and tough ceramic materials are required for many structural applications, however, these properties tend to be mutually exclusive in many man-made ceramic materials. Inspired by composition of biological materials such as nacre, this work offers a simple and versatile 3D printing approach based on the concept of layered ceramics to overcome such limitations, obtaining both high strength and toughness. The resulting layered ceramic/carbon fiber reinforced polymer composites exhibit an excellent combination of high strength, fracture toughness and work of fracture. Such fracture-resistant behavior can be attributed to the toughening mechanisms of crack deflection, lamellae and fiber ‘pull-out’, polymer inelastic deformation, and interfacial debonding. This strategy enables the fabrication of layered ceramic/polymer composites with remarkable properties, thus demonstrating its potential applicability to fabricating other layered composites.

engineering, manufacturing,materials science, multidisciplinary
Strategies for simultaneous strengthening and toughening via nanoscopic intracrystalline defects in a biogenic ceramic

Zhifei Deng,Hongshun Chen,Ting Yang,Zian Jia,James C. Weaver,Pavel D. Shevchenko,Francesco De Carlo,Reza Mirzaeifar,Ling Li

DOI: https://doi.org/10.1038/s41467-020-19416-2

IF: 16.6

2020-11-10

Nature Communications

Abstract:Abstract While many organisms synthesize robust skeletal composites consisting of spatially discrete organic and mineral (ceramic) phases, the intrinsic mechanical properties of the mineral phases are poorly understood. Using the shell of the marine bivalve Atrina rigida as a model system, and through a combination of multiscale structural and mechanical characterization in conjunction with theoretical and computational modeling, we uncover the underlying mechanical roles of a ubiquitous structural motif in biogenic calcite, their nanoscopic intracrystalline defects. These nanoscopic defects not only suppress the soft yielding of pure calcite through the classical precipitation strengthening mechanism, but also enhance energy dissipation through controlled nano- and micro-fracture, where the defects’ size, geometry, orientation, and distribution facilitate and guide crack initialization and propagation. These nano- and micro-scale cracks are further confined by larger scale intercrystalline organic interfaces, enabling further improved damage tolerance.

multidisciplinary sciences
Toughening elastomers via microstructured thermoplastic fibers with sacrificial bonds and hidden lengths

Shibo Zou,Daniel Therriault,Frédérick P. Gosselin

DOI: https://doi.org/10.48550/arXiv.2102.07719

2021-02-15

Soft Condensed Matter

Abstract:Soft materials capable of large inelastic deformation play an essential role in high-performance nacre-inspired architectured materials with a combination of stiffness, strength and toughness. The rigid "building blocks" made from glass or ceramic in these architectured materials lack inelastic deformation capabilities and thus rely on the soft interface material that bonds together these building blocks to achieve large deformation and high toughness. Here, we demonstrate the concept of achieving large inelastic deformation and high energy dissipation in soft materials by embedding microstructured thermoplastic fibers with sacrificial bonds and hidden lengths in a widely used elastomer. The microstructured fibers are fabricated by harnessing the fluid-mechanical instability of a molten polycarbonate (PC) thread on a commercial 3D printer. Polydimethylsiloxane (PDMS) resin is infiltrated around the fibers, creating a soft composite after curing. The failure mechanism and damage tolerance of the composite are analyzed through fracture tests. The high energy dissipation is found to be related to the multiple fracture events of both the sacrificial bonds and elastomer matrix. Combining the microstructured fibers and straight fibers in the elastomer composite results in a ~ 17 times increase in stiffness and a ~ 7 times increase in total energy to failure compared to the neat elastomer. Our findings in applying the sacrificial bonds and hidden lengths toughening mechanism in soft materials at the microscopic scale will facilitate the development of novel bioinspired laminated composite materials with high mechanical performance.
Mechanical behavior of bio-inspired crossed-lamellar microstructures for achieving high-performance composites

Xiaofang Zhang,Yanan Yuan

DOI: https://doi.org/10.1016/j.engfracmech.2023.109397

IF: 5.4

2023-09-01

Engineering Fracture Mechanics

Abstract:The remarkable toughness of Strombus gigas shell arises from its microstructure. In this study, inspired by the biologic crossed-lamellar microstructure of Strombus gigas shell, we prepared a novel carbon fiber reinforced polymer (CFRP) composite with inverse-biologic crossed-lamellar structure by replacing the inner and outer layers with the “tough” middle structure. The influences of the alternating arrangement of crossed-lamellar three-layer structure on the mechanical responses, including toughening mechanisms and biological mechanism, were studied. Experimental and numerical results indicated that as burrowing mollusks, Strombus gigas shells require a balance of certain load-carrying capacity and stronger protection function. Meanwhile, the tailored inverse-biologic structure achieved higher load-bearing capacity and stiffness. Additionally, the Bouligand-ply design strategy was proposed as an alternative to the traditional angle-ply design for the crossed-lamellar structure. By changing the laying-up form and pitch angle of the middle layer, a significant improvement in both load-bearing and energy dissipation capacity of the structures was achieved. The paper provides valuable insights for the design of high-performance biomimetic crossed-lamellar structures and holds great potential for the customization of fiber-reinforced composites.

mechanics
Rigidity-toughness Coupling in Architected Composite Materials for Enhanced Impact Resistance

Zhiquan Wei,Huanbo Wang,Yuanmeng Li,Bo Wang

DOI: https://doi.org/10.1016/j.ijmecsci.2024.109191

IF: 7.3

2024-03-14

International Journal of Mechanical Sciences

Abstract:In recent decades, architected composite materials have received increasing attention due to its promising potential in improving the impact resistance performance compared with bulk materials. Some ingenious microstructures of biomaterials can enlighten the design of novel architected composite materials, such as nacre, conch shell and dactyl club of mantis shrimp, which have been extensively applied. Here, in order to further enhance the impact resistance of architected composite materials, hybrid architectures are proposed based on nacre-like brick-mud and sponge-like lamellar architectures. Then, their impact resistance performances and mechanism are investigated by combining experiment with finite element simulation. The results show that through positive hybrid design inspired of the dactyl club, the lamellar bottom makes the hybrid architecture retain excellent toughness, and the brick-mud top guarantees large flexural stiffness, thereby achieving rigidity-toughness coupling and boosting the energy absorption dramatically. Moreover, as the decline of volume ratio of soft phases within and between brick-mud layers, the energy absorption of brick-mud architecture gradually increases owing to the rising damage resistance. Further, the rigidity-toughness coupled effect can be optimized by positively hybridizing multiple architectures with larger variation in flexural stiffness and toughness, even achieving 375% improvement in energy absorption compared with the basic brick-mud architecture.

engineering, mechanical,mechanics
Hierarchical Toughening of a Biomimetic Bulk Cement Composite

Hao Pan,Wei She,Wenqiang Zuo,Yang Zhou,Jiale Huang,Zhongwen Zhang,Zifan Geng,Yiming Yao,Wenhua Zhang,Li Zheng,Changwen Miao,Jiaping Liu

DOI: https://doi.org/10.1021/acsami.0c15313

2020-11-10

Abstract:Because of the inherent quasibrittleness and heterogeneity, matrix-directed toughening of concrete and cement composites remains to be a huge challenge. Herein, inspired by nacre materials, a novel biomimetic bulk cement composite is fabricated via a facile and efficient process based on compacting prefabricated multisized cement-polymer hybrid prills. This method combines with the three-dimensional "brick–bridge–mortar" structure design and synchronously the intrinsic and extrinsic toughening strategies. Such an approach shows the remarkable maximum toughness enhancement of 27-fold with 71% increase in flexural strength via cooperation with only 4 wt % organic matter. More attractively, it alters the traditional brittle fracture of cement composites to a distinct ductile fracture. In addition, such a biomimetic composite demonstrates the long-term ever-increasing strength and toughness, performing the excellent ductile-fracture retention ability. The hierarchical toughening mechanisms are further revealed with the synergy of microscopic characterizations and simulation methods. This strategy provides a new route for the development of high toughness biomimetic cement-based materials for potential applications in civil engineering domain.The Supporting Information is available free of charge at <a class="ext-link" href="/doi/10.1021/acsami.0c15313?goto=supporting-info">https://pubs.acs.org/doi/10.1021/acsami.0c15313</a>.Details of MD simulations; comparison of detailed fracture surface morphologies; related chemical reactions; molecular structure of pure C–S–H and C–S–H/PAA model; snapshots of the interfacial molecular structure of the C–S–H/PAA composite; RDF and TCF of different interfacial connections in the C–S–H/PAA composite; comparison of the stress–strain curves of pure C–S–H and C–S–H/PAA composite; MSD evolutions of different atoms in tension (z-direction) period; TCF of different connections in the C–S–H/PAA composite in adsorption and tension (z-direction) periods; comparison of the snapshots of pure C–S–H and C–S–H/PAA composite tensioned along the z-direction at different strains; simulated microcrack deflection and crack bridging of the BM structure model via nonlinear FEM simulation (<a class="ext-link" href="/doi/suppl/10.1021/acsami.0c15313/suppl_file/am0c15313_si_001.pdf">PDF</a>)Comparison of mechanical properties of biomimetic bulk cement composite with those of untoughened pure cement bulk and only intrinsically toughened composite under the same strength of impact; comparison of molecule structure evolutions of pure C–S–H and C–S–H/PAA composite in tension period along the z-direction; simulated structure evolution of the BM structure model via nonlinear FEM simulation (<a class="ext-link" href="/doi/suppl/10.1021/acsami.0c15313/suppl_file/am0c15313_si_002.zip">ZIP</a>)This article has not yet been cited by other publications.

materials science, multidisciplinary,nanoscience & nanotechnology

Heart rate levels and ventricular ectopic activity during cardiac rehabilitation.

Conch‐Shell‐Inspired Tough Ceramic

Damage-Tolerance Strategies for Nacre Tablets

Cost-effective Fabrication of Bio-Inspired Nacre-Like Composite Materials with High Strength and Toughness

Reinforcement mechanisms and optimum design of laminated ceramic composites

Fabrication and Characterisation of Alumina/aluminium Composite Materials with a Nacre-Like Micro-Layered Architecture

High-Density 8Mb 1T-1C Ferroelectric Random Access Memory Embedded Within a Low-Power 130nm Logic Process

Energy dissipation in composites with hybrid nacre-like helicoidal microstructures

Printing nature: Unraveling the role of nacre's mineral bridges

Biomimetic structure design — a possible approach to change the brittleness of ceramics in nature

Tough and Ductile Architected Nacre‐Like Cementitious Composites

Tough, Bio-Inspired Hybrid Materials

Artificial Nacre with High Toughness Amplification Factor: Residual Stress‐Engineering Sparks Enhanced Extrinsic Toughening Mechanisms

Tough and Ductile Architected Nacre‐Like Cementitious Composites (Adv. Funct. Mater. 39/2024)

Nacre-like carbon fiber-reinforced biomimetic ceramic composites: Fabrication, microstructure, and mechanical performance

3D printing of layered ceramic/carbon fiber composite with improved toughness

Strategies for simultaneous strengthening and toughening via nanoscopic intracrystalline defects in a biogenic ceramic

Toughening elastomers via microstructured thermoplastic fibers with sacrificial bonds and hidden lengths

Mechanical behavior of bio-inspired crossed-lamellar microstructures for achieving high-performance composites

Rigidity-toughness Coupling in Architected Composite Materials for Enhanced Impact Resistance

Hierarchical Toughening of a Biomimetic Bulk Cement Composite