Abstract:Abstract This paper presents 3D Fabry–Pérot (FP) cavities fabricated directly onto cleaved ends of low-loss optical fibers by a two-photon polymerization (2PP) process. This fabrication technique is quick, simple, and inexpensive compared to planar microfabrication processes, which enables rapid prototyping and the ability to adapt to new requirements. These devices also utilize true 3D design freedom, facilitating the realization of microscale optical elements with challenging geometries. Three different device types were fabricated and evaluated: an unreleased single-cavity device, a released dual-cavity device, and a released hemispherical mirror dual-cavity device. Each iteration improved the quality of the FP cavity’s reflection spectrum. The unreleased device demonstrated an extinction ratio around 1.90, the released device achieved 61, and the hemispherical device achieved 253, providing a strong signal to observe changes in the free spectral range of the device’s reflection response. The reflectance of the photopolymer was also estimated to be between 0.2 and 0.3 over the spectrum of interest. The dual-cavity devices include both an open cavity, which can interact with an interstitial medium, and a second solid cavity, which provides a static reference reflection. The hemispherical dual-cavity device further improves the quality of the reflection signal with a more consistent resonance, and reduced sensitivity to misalignment. These advanced features, which are very challenging to realize with traditional planar microfabrication techniques, are fabricated in a single patterning step. The usability of these FP cavities as thermal radiation sensors with excellent linear response and sensitivity over a broad range of temperature is reported. The 3D structuring capability the 2PP process has enabled the creation of a suspended FP heat sensor that exhibited linear response over the temperature range of 20 oC –120 oC; temperature sensitivity of ∼50 pm oC −1 at around 1550 nm wavelength; and sensitivity improvement of better than 9x of the solidly-mounted sensors.

Tunable Polymer/Air Bragg Optical Microcavity Configurations for Controllable Light-Matter Interaction Scenarios

Toward On-Chip Unidirectional and Single-Mode Polymer Microlaser

Development of High-Quality Polymer/Air-Bragg Micromirror Structures for Nanophotonic Applications

Three-dimensional Fabry–Pérot cavities sculpted on fiber tips using a multiphoton polymerization process

Tunable Ultra‐Narrow Linewidth Light Source Through Liquid Crystal‐Assisted Mini‐Bound‐States‐In‐Continuum Cavities

Tunable Microlasers Modulated by Intracavity Spherical Confinement with Chiral Liquid Crystal

Integrated microcavity optomechanics with a suspended photonic crystal mirror above a distributed Bragg reflector

Direct laser-written optomechanical membranes in fiber Fabry-Perot cavities

Elastomer based electrically tunable, optical microcavities

Photonic molecules made of matched and mismatched microcavities: new functionalities of microlasers and optoelectronic components

Low-loss Tunable 1-D ITO-slot Photonic Crystal Nanobeam Cavity

Multimode vibrational strong coupling in Direct Laser written Mid-IR plasmonic MIM nano-patch antennas

Refractive index matched polymeric and preceramic resins for height-scalable two-photon lithography

Tunable self-assembled Casimir microcavities and polaritons

Laser Micro-Fabrication/Manipulation of Dielectric Materials

Integrative Optofluidic Microcavity with Tubular Channels and Coupled Waveguides Via Two-Photon Polymerization

Bias‐Polarity Dependent Bidirectional Modulation of Photonic Bandgap in a Nanoengineered 3D Blue Phase Polymer Scaffold for Tunable Laser Application

Optical Fabrication of Three-Dimensional Polymeric Microstructures

Additive 3D photonic integration that is CMOS compatible

Pinpoint Two-Photon Writing And Multi-Beam Interferential Patterning Of Three-Dimensional Polymer Photonic Crystals