Abstract:Purpose: The appearance of x-ray luminescence computed tomography (XLCT) opens new possibilities to perform molecular imaging by x ray. In the previous XLCT system, the sample was irradiated by a sequence of narrow x-ray beams and the x-ray luminescence was measured by a highly sensitive charge coupled device (CCD) camera. This resulted in a relatively long sampling time and relatively low utilization of the x-ray beam. In this paper, a novel cone beam x-ray luminescence computed tomography strategy is proposed, which can fully utilize the x-ray dose and shorten the scanning time. The imaging model and reconstruction method are described. The validity of the imaging strategy has been studied in this paper.Methods: In the cone beam XLCT system, the cone beam x ray was adopted to illuminate the sample and a highly sensitive CCD camera was utilized to acquire luminescent photons emitted from the sample. Photons scattering in biological tissues makes it an ill-posed problem to reconstruct the 3D distribution of the x-ray luminescent sample in the cone beam XLCT. In order to overcome this issue, the authors used the diffusion approximation model to describe the photon propagation in tissues, and employed the sparse regularization method for reconstruction. An incomplete variables truncated conjugate gradient method and permissible region strategy were used for reconstruction. Meanwhile, traditional x-ray CT imaging could also be performed in this system. The x-ray attenuation effect has been considered in their imaging model, which is helpful in improving the reconstruction accuracy.Results: First, simulation experiments with cylinder phantoms were carried out to illustrate the validity of the proposed compensated method. The experimental results showed that the location error of the compensated algorithm was smaller than that of the uncompensated method. The permissible region strategy was applied and reduced the reconstruction error to less than 2 mm. The robustness and stability were then evaluated from different view numbers, different regularization parameters, different measurement noise levels, and optical parameters mismatch. The reconstruction results showed that the settings had a small effect on the reconstruction. The nonhomogeneous phantom simulation was also carried out to simulate a more complex experimental situation and evaluated their proposed method. Second, the physical cylinder phantom experiments further showed similar results in their prototype XLCT system. With the discussion of the above experiments, it was shown that the proposed method is feasible to the general case and actual experiments.Conclusions: Utilizing numerical simulation and physical experiments, the authors demonstrated the validity of the new cone beam XLCT method. Furthermore, compared with the previous narrow beam XLCT, the cone beam XLCT could more fully utilize the x-ray dose and the scanning time would be shortened greatly. The study of both simulation experiments and physical phantom experiments indicated that the proposed method was feasible to the general case and actual experiments. (C) 2013 American Association of Physicists in Medicine.

Index matching computerized tomography

A Computed Tomographic Imaging System for Experimentation

Stationary Computed Tomography for Space and other Resource-constrained Environments

Algorithm-driven Advances for Scientific CT Instruments: From Model-based to Deep Learning-based Approaches

Optimization of Image Quality and Acquisition Time for Lab-Based X-ray Microtomography Using an Iterative Reconstruction Algorithm

Meeting the detector challenges for pre-clinical proton and ion computed tomography

A Micro-Ct System For Little Animal Imaging

An Electron Beam Linear Scanning Mode for Industrial Limited-Angle Nano-Computed Tomography.

Design, Optimization and Testing of a Multi-Beam Micro-Ct Scanner Based on Multi-Beam Field Emission X-Ray Technology

Performance Evaluation Of A Prototype Micro-Ct System

Toward a flexible and portable CT scanner

The Birth of the First Ct Scanner

Top-level design and pilot analysis of low-end CT scanners based on linear scanning for developing countries

Online geometry calibration for retrofit computed tomography from a mouse rotation system and a small-animal imager

Synchronous Scanning Mode of Industrial Computed Tomography for Multiple Objects Test.

SU‐FF‐J‐156: High Throughput Micro‐CT Scanner Using a Distributed Multi‐Beam Field Emission X‐Ray Source

WE-E-201B-02: Development of a Tetrahedron Beam Computed Tomography Benchtop System with a 75 Pixel Field Emission X-Ray Tube: System Setup and Performance Evaluation

Design and Simulation Study of a CNT-Based Multisource Cubical CT System for Dynamic Objects.

The Multi-Source Instant CT for Superfast Imaging: System Concept, Reconstruction Algorithms and Experiments

Cone Beam X-Ray Luminescence Computed Tomography: a Feasibility Study.

Electron Tomography Simulator with Realistic 3D Phantom for Evaluation of Acquisition, Alignment and Reconstruction Methods.