Abstract:Ionic liquids, like bis(fluorosulfonyl)imide (FSI) ionic liquids, are promising solvents for lithium ion batteries due to their high thermal stability and wide electrochemical window. The performance of ionic liquid electrolytes is however hampered by the low conductivity at room temperature, but the high thermal stability allows for operation at elevated temperatures, at which the conductivity is significantly improved. Electrolytes based on LiFSI and ionic liquids of the cations; pyrrolidinium (PYR13 +), and phosphonium (P111i4 +), with FSI anions, have been shown to exhibit stable cycling at room temperature, and good rate performance for cells composed of silicon anodes and LiFePO4 cathodes at 60 °C [1,2]. The lithium ion mobilities, relative to standard carbonate electrolytes, were determined from the limiting current densities at room temperature and 60 °C. Significant differences in the temperature dependence of the transport properties were revealed, with a considerable increase in the lithium ion mobility from 20 to 60 °C for electrolytes based on P111i4FSI. The best rate performance at 60 °C was demonstrated for the P111i4FSI based electrolyte, with discharge capacities around 1000 mAh/gSi at a 2C rate [2]. The improved performance was attributed to a combination of the improved lithium ion mobility and formation of a more conductive solid electrolyte interphase (SEI) for this electrolyte. In view of the excellent high temperature performance of P111i4FSI, including high thermal stability and a large electrochemical window [1,2], this electrolyte has been selected for further studies as electrolyte for high voltage LiNi0.5-xMn1.5+xO4 (LNMO) cathodes. LiNi0.5-xMn1.5+xO4 (LNMO) is an attractive candidate as a next generation Li-ion battery (LIB) cathode material because it has a high energy density, due to the high operating voltage, and a relatively low cost (Co-free) compared to alternative cathode chemistries. However, the stability of LNMO is not yet satisfactory for commercial applications, especially in full-cell configuration with graphite as the anode material, and at elevated temperatures. One challenge is the transition metal (TM) dissolution, which poisons the graphite anode by degrading the solid electrolyte interface (SEI) [4]. The TM dissolution is affected by the formation of hydrofluoric (HF) acid in carbonate-based electrolytes utilizing the LiPF6 salt [3]. Additionally, the decomposition processes occur with an increased rate at elevated temperatures [4,5]. Another challenge is the side reactions occurring at the high operating voltage, which limits the coulombic efficiency. Previous works have indicated that the carbon conductive additive is more prone to side reactions than the LNMO active material [6]. Here, we present a study on the phosphonium-based ionic liquid P111i4FSI, with two different salt concentrations: 0.79 m LiFSI and 3.0 m LiFSI, as an alternative electrolyte for LIBs with an LNMO cathode.The focus of the research is to study the side reactions separately on the carbon conductive additive, and on the LNMO active material. Carbon conductive additives differing in structure and particle size are studied. The electrolyte is tested both in half-cell and full-cell configuration with a graphite anode, as well as at room temperature and elevated temperatures. Using 0.79 m LiFSI P111i4FSI results in similar capacity retention, but higher coulombic efficiencies after 200 cycles in half-cells at room temperature compared to 1 M LiPF6 in 1:1 EC:DEC (v/v). Post-mortem characterization is carried out with SEM, TEM, Raman spectroscopy, and FT-IR. References [1] D.T. Rogstad et al., J. Electrochem. Soc., 168 (2021) 110506 [2] Daniel Tevik Rogstad et al. 2022 Journal of the Electrochemical Society, 169, 110531 [3] Marc Wentker et al. 2019 Energies, 12, 504 [4] Nicholas P. W. Pieczonka et al. 2013 The Journal of Physical Chemistry C 117, 15947-15957 [5] U. Heider et al. 1999 Journal of Power Sources 81-82, 119-122, [6] Younesi et al., J. Electrochem. Soc., 162(7) (2015) A1289

Counteracting thermal degradation of LiPF 6 -based electrolyte with additives or lithium salts: A gas analysis revealing the impact of NMC

Effects of Components in Solvent-Enhanced PVDF-HFP-Based Polymer Electrolyte on Its Electrochemical Performance

Unraveling and Mitigating the Storage Instability of Fluoroethylene Carbonate-Containing LiPF6 Electrolytes to Stabilize Lithium Metal Anodes for High-Temperature Rechargeable Batteries

Synergistic Dual-Additive Regulated Carbonate Electrolyte Stabilizes Bidirectional Interface for Aggressive Ni-rich Li-metal Full Batteries

Practical 4.4 V Li||NCM811 batteries enabled by a thermal stable and HF free carbonate-based electrolyte

Investigation of Gas Evolution by Operando GC/MS from SEI Forming Additives in Lithium-Ion-Batteries

Thermal stability analysis of nitrile additives in LiFSI for lithium-ion batteries: An accelerating rate calorimetry study

Enhanced Aluminium Passivation properties of lithium nonafluoro-tert-butoxide: Designing Electrolyte Additives for High-Voltage 4.8 V LiNi0.5Mn1.5O4-graphite batteries

LiTDI: A Highly Efficient Additive for Electrolyte Stabilization in Lithium-Ion Batteries

A Ternary Additive Mixture for Suppressed Electrolyte Decomposition and Mitigated Gassing in 5V Lnmo‖Graphite Li-Ion Cells

Revealing the Influence of Electrolyte Additives in Reducing the Heat Generation of High Voltage Lithium‐Ion Batteries using Operando Accelerating Rate Calorimetry (ARC)

The Role of LiTDI Additive in LiNi1/3Mn1/3Co1/3O2/ Graphite Lithium-Ion Batteries at Elevated Temperatures

Investigating Cathode Electrolyte Interphase Formation in NMC 811 Primary Particles through Advanced 4D-STEM ACOM Analysis

Stable Non‐flammable Phosphate Electrolyte for Lithium Metal Batteries via Solvation Regulation by the Additive

Combined Stabilizing of the Solid-Electrolyte Interphase with Suppression of Graphite Exfoliation via Additive-Solvent Optimization in Li-Ion Batteries

Enhanced Electrochemical Performance of Ni‐Rich Layered Cathode Materials by Using LiPF6 As a Cathode Additive

LiPO2F2 as a LiPF6 Stablizer Additive to Improve the high- temperature Performance of the NCM811/SiOx@C Battery

High reactivity of the nickel-rich LiNi1-x-yMnxCoyO2 layered materials surface towards H2O/CO2 atmosphere and LiPF6-based electrolyte

Phenyl 4-Fluorobenzene Sulfonate as a Versatile Film-Forming Electrolyte Additive for Wide-Temperature-Range NCM811//Graphite Batteries

Evaluation of Electrolytes Containing Flame Retardant Additives in LiNixCo1-xO2 and Li(Li0.17Ni0.25Mn0.58)O2-Based Li-Ion Cells

Phosphonium-Based Ionic Liquid Electrolyte in Combination with Silicon Anodes and LiNi0.5-XMn1.5+XO4 Cathodes for Lithium Ion Batteries