Abstract:As an important part of human-computer interactions in a smart city, wearable electronics and sensors have grown significantly and often require energy autonomy for an extended service time without the frequent recharging and replacement of batteries. The conversion of the temperature difference between the skin and the ambient environment into electricity via a thermoelectric generator (TEG) is useful for wearable self-powered electronic systems. In this work, flexible polyimide with copper metalized on one side and copper electrodes patterned on the other side acts as a substrate. The inorganic materials of P-type Bi0.5Sb1.5Te3 and N-type Bi2Se0.3Te2.7, with excellent performance around room temperature, serve as the thermoelectric legs. To ensure the generator some flexibility, the upper substrate is cut into blocks without affecting the electrical path. For the initial TEG (size: 2 x 16 mm(2) in plane, fill factor: 16.25%, TE leg: 0.4 x 0.4 x 0.5 mm(3)), the internal resistance of the device is basically maintained at 1.15 omega at each time in a bending process within the error range. Furthermore, after 10 000 bending cycles, the internal resistance and the open circuit voltage (T-h = 33 degrees C, T-c = 23 degrees C) of the micro-TEG with FFs of 6.32%, 9.93% and 16.25% show almost no change. For the optimized TEG worn on the arm or forehead (size: 40 x 100 mm(2) in plane, TE leg: 1.4 x 1.4 x 1.6 mm(3)), heat collection with a copper film at the skin end and a copper foam (porosity: >95%) heat sink at the air end were installed to improve the power generation performance of the TEG. A maximum open circuit voltage of 536.2 mV and power density of 454.9 mu W cm(-2) can be achieved for the TEG with a 20% FF under a temperature difference of 10 degrees C (T-h = 33 degrees C, T-c = 23 degrees C). And the generator can continuously generate a maximum open circuit voltage of 97 mV with a heat source of 50 degrees C after being equipped with a heat sink. When the wearer is running outdoors (wind speed similar to 3 m s(-1)), the power density is greatly improved to 138.46 mu W cm(-2) from 4.66 mu W cm(-2) (wind speed similar to 0 m s(-1)). These results are among the best performances reported for flexible TEGs and are sufficient to drive microwatt-level electronic sensors. This work provides a feasible method for wearable and charge-free electronic devices.

Partially Air‐Filled Skin‐Attachable Deformable Gasket with Negative Poisson's Ratio for Highly‐Efficient Stretchable Thermoelectric Generators

Partially Air‐Filled Skin‐Attachable Deformable Gasket with Negative Poisson's Ratio for Highly‐Efficient Stretchable Thermoelectric Generators (Adv. Energy Mater. 40/2023)

A Cross‐Plane Design for Wearable Thermoelectric Generators with High Stretchability and Output Performance

Design and Fabrication of Wearable Thermoelectric Generator Device for Heat Harvesting

Comprehensive Performance Prediction and Power Promotion for Wearable Thermoelectric Generator with Flexible Encapsulation in Practical Application

A Wavy-Structured Highly Stretchable Thermoelectric Generator with Stable Energy Output and Self-Rescuing Capability

Design of a Wearable Thermoelectric Generator for Harvesting Human Body Energy

Operation of Wearable Thermoelectric Generators Using Dual Sources of Heat and Light

High‐Performance Stretchable Thermoelectric Generator for Self‐Powered Wearable Electronics

Kirigami-Based Stretchable, Deformable, Ultralight Thin-Film Thermoelectric Generator for BodyNET Application

Optimized thermal design for excellent wearable thermoelectric generator

High‐performance Stretchable Organic Thermoelectric Generator via Rational Thermal Interface Design for Wearable Electronics

High-Performance Wearable Bi2Te3-Based Thermoelectric Generator

Soft and Stretchable Thermoelectric Generators Enabled by Liquid Metal Elastomer Composites

Simultaneous Realization of Flexibility and Ultrahigh Normalized Power Density in a Heatsink-Free Thermoelectric Generator via Fine Thermal Regulation

A High-Performance Wearable Thermoelectric Generator with Comprehensive Optimization of Thermal Resistance and Voltage Boosting Conversion

Persistently Self-Powered Wearable Thermoelectric Generator Enabled by Phase-Change Inorganics As the Heat Sink

Initiating a Stretchable, Compressible, and Wearable Thermoelectric Generator by a Spiral Architecture with Ternary Nanocomposites for Efficient Heat Harvesting

Bi<sub>2</sub>Te<sub>3</sub>-based wearable thermoelectric generator with high power density: from structure design to application

Stretchable thermoelectric generator for wearable power source and temperature detection applications

Flexible micro thermoelectric generators with high power density and light weight