Abstract:A kind of branched block PBI proton exchange membrane (PEM) has a porphyrin ring structure for HT‐PEMFCs application. Uses low‐content porphyrin rings (<1 mol.%) as branched monomers to prepare branched PBI, maintaining a high level of PA doping and retention ability. The membranes achieve high proton conductivity and enhance fuel cell performance through the synergistic effect of phase separation of block structures and porphyrin π−π stacking. This results in a uniform distribution of high‐density helical nanochannels that through‐out the membrane, but present better chemical stability and maintains high levels of PA doping and retention ability. The membrane electrode assembly (MEA) can achieve an H2‐O2 fuel cell peak power density of 1077 mW cm−2 at 180 °C and 357 mW cm−2 at 80 °C without humidification and backpressure. High‐temperature proton‐exchange membrane fuel cells (HT‐PEMFCs) fabricated with phosphoric acid (PA)‐doped polybenzimidazole (PBI) show apparent technical advantages. In practical automotive applications, achieving cold start‐up capability is crucial. In this work, a kind of branched block proton exchange membrane (PEM) based on PBI with a low content of porphyrin ring (<1 mol.%) is reported as a branched monomer. Self‐assembly into high‐density helical nanochannels under the synergistic effect of phase separation and porphyrin π−π stacking, thus the PEM can maintain a high level of PA doping. Specifically, the PA/1.8TCPP‐BrPy‐OPBI membrane shows a proton conductivity of 0.169 and 0.071 S cm−1, as well as an H2‐O2 fuel cell peak power density of 1077 and 357 mW cm−2 at 180 and 80 °C without humidification and backpressure, respectively. The membrane electrode assembly (MEA) can exhibit good fuel cell stability, with a voltage decay rate of only 7.0 μV h−1 at 80 °C. Furthermore, it maintains a peak power density of 93% even after 150 start‐up/shut‐down cycles at 25 °C. This work expands the operating temperature range of conventional PBI membranes between 25 and 200 °C and thus provides a novel strategy for high‐performance PBI‐based HT‐PEMFCs.

Self-assembled network polymer electrolyte membranes for application in fuel cells at 250 °C

Polybenzimidazole/ionic-liquid-functional Silica Composite Membranes with Improved Proton Conductivity for High Temperature Proton Exchange Membrane Fuel Cells

Composite Membranes Based on Polybenzimidazole and Ionic Liquid Functional Si–O–Si Network for HT-PEMFC Applications

Gel-state Polybenzimidazole Proton Exchange Membranes with Flexible Alkyl Sulfonic Acid Side Chains for a Wider Operating Temperature Range (25–240 °C)

Polybenzimidazole and ionic liquid composite membranes for high temperature polymer electrolyte fuel cells

Polyethyleneimine-filled Sepiolite Nanorods-Embedded Poly(2,5-Benzimidazole) Composite Membranes for Wide-Temperature PEMFCs

Porphyrin Helical Nanochannel‐Assembled Polybenzimidazole Membranes Doped with Phosphoric Acid for Fuel Cells Operating in a Temperature Range of 25–200 °C

High CO Tolerance of New SiO2 Doped Phosphoric Acid/polybenzimidazole Polymer Electrolyte Membrane Fuel Cells at High Temperatures of 200–250 °C

Ionically Crosslinked Composite Membranes from Polybenzimidazole and Sulfonated Poly (fluorenyl ether ketone) for High-Temperature PEM Fuel Cells

Self-Phosphorylated Polybenzimidazole: An Environmentally Friendly and Economical Approach for Hydrogen/Air High-Temperature Polymer-Electrolyte Membrane Fuel Cells

Sulfonated poly(ether ether ketone)-Protic ionic Liquid-Based anhydrous Proton-Conducting composite polymer electrolyte membranes for High-Temperature fuel cell applications

High ion exchange capacity perfluorosulfonic acid resine proton exchange membrane for high temperature applications in polymer electrolyte fuel cells

Synthesis and Properties of Polysilsesquioxane Functionalized Poly(p‐terphenyl‐co‐N‐methyl‐4‐piperidine) Membrane for High Temperature Proton Exchange Membrane Fuel Cells

Finely Adjusted Intrinsically Microporous Copolyimide Electrolyte Membranes for Fuel Cells Operating in a Wide Temperature Range

Dual cross-linked polymer electrolyte membranes based on poly(aryl ether ketone) and poly(styrene-vinylimidazole-divinylbenzene) for high temperature proton exchange membrane fuel cells

Fabrication of high performance high-temperature proton exchange membranes through constructing stable cation-rich domain in polybenzimidazole membrane

Double cross-linked 3D layered PBI proton exchange membranes for stable fuel cell performance above 200 °C

Polybenzimidazole/cerium dioxide/graphitic carbon nitride nanosheets for high performance and durable high temperature proton exchange membranes

Core-shell tin pyrophosphate-based composite membrane for fuel cell with durability enhancement at elevated temperatures

Antioxidant Sulfide‐Linked Polymer Membrane with Inherent Microporosity Enables Fuel Cells to Achieve Outstanding Power Density and Durability Over a Wide Temperature Range

Achieving high power density and excellent durability for high temperature proton exchange membrane fuel cells based on crosslinked branched polybenzimidazole and metal-organic frameworks