Abstract:Dihydrogen (H2) is considered nowadays as a sustainable energy carrier and exhibits a high energy density in its highly compressed state. Different countries in the world are developing industrial production and are scaling up water electrolysis processes with clear roadmaps. Alkaline water electrolysis is an affordable technology that avoids the use of platinum group metals with a good compromise of efficiency because of the development of new cost-effective and Earth-abundant materials of electrodes and new anion-exchange membranes. Here, we report on the use of emerging and selective laser melting (SLM) technology for the three-dimensional (3D) printing of binary alloyed NiFe, NiMo, NiCr, and NiCo electrode materials at an applied scale. These materials are preliminarily tested for hydrogen and oxygen evolution half-reactions in alkaline conditions to select the most promising combinations of cathode/anode combinations for overall water electrolysis. On the basis of three key performance metrics (KPMs, namely, overpotential values at 10 and 50 mA cm–2 and the stability in operation over 6 days at 50 mA cm–2), NiCr and NiCo are preferred for the cathode, whereas the anode is NiMo or NiFe. Moreover, to facilitate the release of the electrogenerated gas bubbles, the patterning of 3D-printed electrodes with either roughly conical holes or ramps is considered as a third experimental factor. The water electrolysis process is then fully optimized using the formalism of design of experiments (DOE), which allows to reduce the number of experiments without loss in the quality of conclusions. This study reveals that NiCo and NiMo will be preferentially used as the cathode and anode, respectively, to decrease the cell overvoltage, whereas NiFe as the anode yields the best stability in operation. Besides, the impact of the patterns printed by SLM on the KPMs is somewhat limited, even though the presence of holes is rather beneficial for decreasing cell overvoltage. Interestingly, an approximate calculation of the consumed energy for the production of 1 kg of H2 from the combination of NiCo/NiMo/holes as the cathode/anode/pattern yields 50.6 kWh/kg of H2, which is quite promising if one refers to the 48 kWh industrial target set by European Union for 2030.

Optimization of hydrogen production via electrocatalysis using NiCoMo-modified electrodes: An RSM approach

Alloying Nickel with Molybdenum Significantly Accelerates Alkaline Hydrogen Electrocatalysis

In Situ Construction of Ni Enriched Porous NiAl As Long-Lived Electrode for Hydrogen Evolution at High Current Densities

Interface Engineering: the Ni(Oh)(2)/Mos2 Heterostructure for Highly Efficient Alkaline Hydrogen Evolution

Simultaneous Interfacial Chemistry and Inner Helmholtz Plane Regulation for Superior Alkaline Hydrogen Evolution

Improving alkaline hydrogen evoluation reaction efficiency through 1T/2H-MoS2/Ni3S2 heterostructure design

Hydrogen production by traditional and novel alkaline water electrolysis on nickel or iron based electrocatalysts.

Electrocatalytic and structural investigation of trimetallic NiFeMo bifunctional electrocatalyst for industrial alkaline water electrolysis

Indirect electrodeposition of a NiMo@Ni(OH)2MoO composite catalyst for superior hydrogen production in acidic and alkaline electrolytes

Synergistic Electrocatalytic Hydrogen Evolution in Ni/NiS Nanoparticles Wrapped in Multi-Heteroatom-Doped Reduced Graphene Oxide Nanosheets.

Nickel and titanium metals for the hydrogen evolution reaction in water electrolysis: A comparative study

Vertical Graphene-Supported NiMo Nanoparticles as Efficient Electrocatalysts for Hydrogen Evolution Reaction under Alkaline Conditions

Hierarchical Crystalline/Amorphous Heterostructure MoNi/NiMoOx for Electrochemical Hydrogen Evolution with Industry‐Level Activity and Stability

Optimization of Three-Dimensional-Printed Catalytic Electrodes for Alkaline Water Electrolysis Guided by the Experimental Design Methodology

Efficient Hydrogen Evolution Electrocatalyst: MoN/Ni 3 N/NF Coupled with Methanol Oxidation Reaction for Formate Production in Alkaline Media

Optimizing electronic structure of porous Ni/MoO2 heterostructure to boost alkaline hydrogen evolution reaction

The Optimization of a Physical Factor of Hydrogen Production in Alkaline Water Electrolysis

Synthesis of NiMoO4/NiMo@NiS Nanorods for Efficient Hydrogen Evolution Reactions in Electrocatalysts

Statistical optimization of hydrogen production from bio-methanol steam reforming over Ni-Cu/Al2O3 catalysts

Optimizing NiFe-Modified Graphite for Enhanced Catalytic Performance in Alkaline Water Electrolysis: Influence of Substrate Geometry and Catalyst Loading

Heterostructured Ni–Mo–N nanoparticles decorated on reduced graphene oxide as efficient and robust electrocatalyst for hydrogen evolution reaction