Abstract:Lithium–sulfur (Li–S) batteries are severely hindered by the low sulfur utilization and short cycling life, especially at high rates. One of the effective solutions to address these problems is to improve the sulfiphilicity of lithium polysulfides (LiPSs) and the lithiophilicity of the lithium anode. However, it is a great challenge to simultaneously optimize both aspects. Herein, by incorporating the merits of strong absorbability and high conductivity of SnS with good catalytic capability of ZnS, a ZnS-SnS heterojunction coated with a polydopamine-derived N-doped carbon shell (denoted as ) with uniform cubic morphology was obtained and compared with the ZnS-SnS2@NC heterostructure and its single-component counterparts ( and SnS2@NC). Theoretical calculations, ex situ XANES, and in situ Raman spectrum were utilized to elucidate rapid anchoring-diffusion-transformation of LiPSs, inhibition of the shuttling effect, and improvement of the sulfur electrochemistry of bimetal ZnS-SnS heterostructure at the molecular level. When applied as a modification layer coated on the separator, the cell with optimized lithiophilicity and sulfiphilicity enables desirable sulfur electrochemistry, including high reversibility of 1149 mAh g–1 for 300 cycles at 0.2 C, high rate performance of 661 mAh g–1 at 10 C, and long cycle life with a low fading rate of 0.0126% each cycle after 2000 cycles at 4 C. Furthermore, a favorable areal capacity of 8.27 mAh cm–2 is maintained under high sulfur mass loading of 10.3 mg cm–2. This work furnishes a feasible scheme to the rational design of bimetal sulfides heterostructures and boosts the development of other electrochemical applications.The Supporting Information is available free of charge at <a class="ext-link" href="/doi/10.1021/acsnano.1c00270?goto=supporting-info">https://pubs.acs.org/doi/10.1021/acsnano.1c00270</a>.Additional experimental sections (materials synthesis, characterizations, and DFT calculations); SEM, TEM, XRD, TG, XPS, BET, and XANES characterizations of the samples; CV curves; discharge–charge profiles and cycle performance of various electrodes; in situ Raman tests; optimized geometries of LiPSs; Tables S1–S6: Li+ diffusion rates, EIS fitting, and comparisons of electrochemical performance (<a class="ext-link" href="/doi/suppl/10.1021/acsnano.1c00270/suppl_file/nn1c00270_si_001.pdf">PDF</a>)This article has not yet been cited by other publications.

Quantitative defect regulation of heterostructures for sulfur catalysis toward fast and long lifespan lithium-sulfur batteries

Enhanced catalysis LiS<sub>3</sub> of radical-to-polysulfide interconversion <i>via</i> increased sulfur vacancies in lithium-sulfur batteries

Design Unsaturated Selenium Coordinated NbSe2‐x as Multifunctional Sulfur Electrocatalyst toward Fast and Durable Sulfur Reduction Reaction

Quantitatively regulating defects of 2D tungsten selenide to enhance catalytic ability for polysulfide conversion in a lithium sulfur battery

Defective VSe2-Graphene Heterostructures Enabling in Situ Electrocatalyst Evolution for Lithium-Sulfur Batteries.

Ni0.85Se/NiSe2-C electrocatalyst with defect engineering and heterostructure for the multifunctional acceleration of lithium polysulfide conversion

Defect-engineered Sulfur Vacancy Modified NiCo2 S4-x Nanosheet Anchoring Polysulfide for Improved Lithium Sulfur Batteries

Manipulating Electrocatalytic Li 2 S Redox via Selective Dual‐Defect Engineering for Li–S Batteries

Synergizing Spatial Confinement and Dual‐Metal Catalysis to Boost Sulfur Kinetics in Lithium–Sulfur Batteries

Defective VSe 2 –Graphene Heterostructures Enabling In Situ Electrocatalyst Evolution for Lithium–Sulfur Batteries

Defect-Rich Multi-shelled Fe-doped Co3O4 Hollow Microspheres with Multiple Spatial Confinements to Facilitate Catalytic Conversion of Polysulfides for High-Performance Li-S Batteries.

Enhanced Polysulfide Conversion with Highly Conductive and Electrocatalytic Iodine‐Doped Bismuth Selenide Nanosheets in Lithium–Sulfur Batteries

Defect-riched prussian blue analogues with superior adsorption-catalysis toward lithium polysulfides for high performance lithium-sulfur batteries

Enhanced Polysulfide Regulation <i>via</i> Porous Catalytic V<sub>2</sub>O<sub>3</sub>/V<sub>8</sub>C<sub>7</sub> Heterostructures Derived from Metal-Organic Frameworks toward High-Performance Li-S Batteries

A Combined Ordered Macro‐Mesoporous Architecture Design and Surface Engineering Strategy for High‐Performance Sulfur Immobilizer in Lithium–Sulfur Batteries

Propelling Polysulfide Conversion by Defect-Rich MoS2 Nanosheets for High-Performance Lithium-Sulfur Batteries

ZnS-SnS@NC Heterostructure as Robust Lithiophilicity and Sulfiphilicity Mediator toward High-Rate and Long-Life Lithium–Sulfur Batteries

A High‐Efficiency CoSe Electrocatalyst with Hierarchical Porous Polyhedron Nanoarchitecture for Accelerating Polysulfides Conversion in Li–S Batteries

Defective TiO2-graphene heterostructures enabling in-situ electrocatalyst evolution for lithium-sulfur batteries

Bimetallic sulfides heterostructure efficient adsorption and catalytic of polysulfides for high-performance lithium-sulfur batteries

The role of selenium vacancies functionalized mediator of bimetal (Co, Fe) selenide for high-energy-density lithium-sulfur batteries