Abstract:Hydrogen has been largely proposed as a possible fuel for internal combustion engines. The main advantage of burning hydrogen is the absence of carbon-based tailpipe emissions. Hydrogen's wide flammability also offers the advantage of very lean combustion and higher engine efficiency than conventional carbon-based fuels. In order to avoid abnormal combustion modes like pre-ignition and backfiring, as well as air displacement from hydrogen's large injected volume per cycle, direct injection of hydrogen after intake valve closure is the preferred mixture preparation method for hydrogen engines. The current work focused on computational studies of hydrogen injection and mixture formation for direct-injection spark-ignition engines. Hydrogen conditions at the injector's nozzle exit are typically sonic. Initially the characteristics of under-expanded sonic hydrogen jets were investigated in a quiescent environment using both Reynolds-Averaged Navier-Stokes (RANS) and Large-Eddy Simulation (LES) techniques. Various injection conditions were studied, including a reference case from the literature. Different nozzle geometries were investigated, including a straight nozzle with fixed cross section and a stepped nozzle design. LES captured details of the expansion shocks better than RANS and demonstrated several aspects of hydrogen's injection and mixing. In-cylinder simulations were also performed with a side 6-hole injector using 70 and 100 bar injection pressure. Injection timing was set to just after inlet valve closure with duration of 6 μs and 8 μs, leading to global air-to-fuel equivalence ratios ϕ typically in the region of 0.2-0.4. The engine intake air pressure was set to 1.5 bar absolute to mimic boosted operation. It was observed that hydrogen jet wall impingement was always prominent. Comparison with non-fuelled engine conditions demonstrated the degree of momentum exchange between in-cylinder hydrogen injection and air motion. LES highlighted details of hydrogen's spatial distribution throughout the injection duration and up to ignition timing. Higher peak velocities were predicted by LES, especially on the tumble plane. With the employed injection strategy, the areas closer to the cylinder wall were richer in fuel than the centre of the chamber close to the end of compression.

Drag Control by Hydrogen Injection in Shocked Stagnation Zone of Blunt Nose

Numerical Study of Heat Flux Reduction Mechanism of the Counterflowing Jet in Rarefied Flows

Stabilization regimes and pollutant emissions from a dual fuel CH4/H2 and dual swirl low NOx burner

Computational Study of Lateral Jet Interaction in Hypersonic Thermochemical Non-Equilibrium Flows Using Nonlinear Coupled Constitutive Relations

Direct Numerical Simulation of Skin Friction Drag Reduction on Supersonic Turbulent Boundary Layers with Micro-Blowing

Effect of counterflow argon plasma jet on aerodynamic drag of a blunt body at hypersonic Mach numbers

Heat and drag reduction on the hypersonic nose with a nexus between active and passive control methods

Aero Heating Optimization of a Hypersonic Thermochemical Non-Equilibrium Flow around Blunt Body by Application of Opposing Jet and Blunt Spike

Coupled fluid–thermal analysis of the reduction mechanism for the drag and heat flux induced by jet interaction in a hypersonic reusable launch vehicle

Multi Parameters Control Mechanism on Drag and Heat Reduction of Opposing Jet

Evaluation of Various Flow Control Methods in Reducing Drag and Aerodynamic Heating on the Nose of Hypersonic Flying Objects

Computational Study of Drag Reduction at Various Freestream Flows Using A Counterflow Jet from A Hemispherical Cylinder

Numerical and Experimental Investigation on Nosebleed Air Jet Control for Hypersonic Vehicle

Heat and drag reduction of single and combined opposing jets in hypersonic nonequilibrium flows

Numerical study on drag and heat flux reduction induced by a counterflowing jet for rarefied hypersonic flow over a blunt body

Computational Study of Hydrogen Direct Injection for Internal Combustion Engines

Research on a novel combined shock control mechanism for thermal protection and drag reduction in hypersonic compressible flow field

Characterizing and visualizing the direct injection of hydrogen into high-pressure argon and nitrogen environments

Study on hypersonic drag and heat reduction of a spiked blunt body with multiple flat aerodisks and rear opposing jets

Assessment on jet direction effect on drag and heat reduction efficiency for hypersonic vehicles