Abstract:Bacterial nanocellulose (BNC) was used to synthesize rigid polyurethane foams (RPUFs) based on its reaction with the isocyanate precursor (ISO route) and also by using the conventional procedure (POL route). The results indicated that at only 0.1 wt. % of BNC, drastic improvements of specific elastic compressive modulus (+244.2 %) and strength (+77.5 %) were found. The reaction of BNC with the precursor was corroborated through the measurement of isocyanate number and the BNC caused a significant nucleation effect, decreasing the cell size up to 39.7%. DSC analysis revealed that the BNC had a strong effect on post-cure enthalpy, decreasing its value when the ISO route was implemented. DMA analysis revealed that the RPUFs developed using the ISO route proved to have an improved damping factor, regardless of BNC concentration. These results emphasize the importance of using the ISO route to achieve foamed nanocomposites with improved specific mechanical properties.

What problem does this paper attempt to address?

The problem that this paper attempts to solve is to improve the specific thermomechanical properties of Rigid Polyurethane Foams (RPUFs) by using Bacterial Nanocellulose (BNC) as the Hard Segment. Specifically, the author hopes that by introducing BNC, not only can the mechanical properties of RPUFs (such as elastic compressive modulus and strength) be improved, but also the cell size can be reduced, and the influence of different introduction paths (i.e., POL route and ISO route) on the final properties of the material can be explored. ### Main problems and goals 1. **Improve mechanical properties**: By adding 0.1 wt.% of BNC, the experimental results show that the elastic compressive modulus is increased by 244.2% and the strength is increased by 77.5%. 2. **Reduce cell size**: The introduction of BNC significantly reduces the cell size, with a maximum reduction of 39.7%. 3. **Optimize the introduction path**: The effects of two introduction paths (POL route and ISO route) on the material properties are compared, and it is found that the ISO route performs well in improving the damping factor and is not affected by the BNC concentration. 4. **Sustainable development**: Explore the possibility of using renewable resources (such as BNC) to replace traditional non - renewable resources to improve the sustainability of materials. ### Solutions - **Use BNC as a hard segment**: As a two - dimensional nanoparticle, BNC has a high specific surface area and good biocompatibility, and can significantly improve the material properties at a low concentration. - **Comparison of different introduction paths**: - **POL route**: BNC is dispersed in polyol without a chemical reaction, mainly relying on physical dispersion. - **ISO route**: BNC reacts with isocyanate precursor to form a chemical bond, ensuring that BNC functions as a hard segment. ### Experimental results - **Improvement of mechanical properties**: By introducing BNC, especially by using the ISO route, the elastic compressive modulus and strength of the material are significantly improved. - **Reduction of cell size**: The introduction of BNC leads to a significant reduction in cell size, especially in the ISO route, the effect is more obvious. - **Improvement of thermomechanical properties**: DMA analysis shows that the RPUFs prepared by the ISO route have a better damping factor, indicating that it performs excellently in vibration and shock absorption. ### Conclusion This study emphasizes the importance of introducing BNC by using the ISO route. This method can not only significantly improve the specific thermomechanical properties of RPUFs, but also provides new ideas for developing polyurethane materials with a higher renewable content.

Nanostructured rigid polyurethane foams with improved specific thermo-mechanical properties using Bacterial Nanocellulose as a Hard Segment

Stiffness, Energy Dissipation, and Hyperelasticity in Hierarchical Multilayer Composite Nanocoated Open‐Cell Polyurethane Foams

Effect of Surface Modification of Montmorillonite on the Properties of Rigid Polyurethane Foam Composites

Preparation of Cellulose/MWCNTs/TPU Micro-foam Composites

Mechanical and Insulation Performance of Rigid Polyurethane Foam Reinforced with Lignin-Containing Nanocellulose Fibrils

Micro fibrillated cellulose reinforced bio-based rigid high-density polyurethane foams

Effect of Different Methods to Synthesize Polyol-Grafted-Cellulose Nanocrystals as Inter-Active Filler in Bio-Based Polyurethane Foams

Synthesis of bio-polyol-functionalized nanocrystalline celluloses as reactive/reinforcing components in bio-based polyurethane foams by homogeneous environment modification

Polyurethane Nanocomposites with Open-Cell Structure Modified with Aluminosilicate Nano-Filler

Carbamate Thermal Decarboxylation for the Design of Non-Isocyanate Polyurethane Foams

Effects of cellulose micro and nanocrystals on the mechanical, thermal, morphological, and structural properties of rigid polyurethanes

Composites of rigid polyurethane foams and silica powder filler enhanced with ionic liquid

Synthesis and characterization of bio‐based poly(urethane‐urea) nanocomposite coatings employing cellulose nanocrystals incorporated by two different routes

Chemically Functionalized Cellulose Nanocrystals as Reactive Filler in Bio-Based Polyurethane Foams

Characterization of carbon nanofibre-reinforced polypropylene foams

Synthesis and Effect of Nanocellulose Obtained from East Java Kenaf Fiber on Mechanical Properties of Polyurethane Foam Composites as Strong and Lightweight Materials

Preparation and fire resistance modification on tannin-based non-isocyanate polyurethane (NIPU) rigid foams

Thermomechanical Behavior Of Polyurethane Nanocomposite Foams Containing Organoclay Particles Modified With Bio-Based Fatty Acid

Preparation of Bio-Based Foams with a Uniform Pore Structure by Nanocellulose/Nisin/Waterborne-Polyurethane-Stabilized Pickering Emulsion

Synthesis, Characterization and Mechanical Properties of Novel Bio-Based Polyurethane Foams Using Cellulose-Derived Polyol for Chain Extension and Cellulose Citrate as a Thickener Additive

Ultralight cellulose nanofiber based foams: the effects of material formulation and nanofiber type on mechanical properties and thermal insulation