Beam Loss Monitors

Kay Wittenburg

DOI: https://doi.org/10.48550/arXiv.2005.06522

2020-05-14

Abstract:This lecture covers the fundamental aspects of the measurement of beam losses including their use for beam diagnostic and safety issues. The detailed functionality and detection principle of various common beam loss monitors are also presented, with a focus on their intrinsic sensitivity.

Accelerator Physics

What problem does this paper attempt to address?

Development of fiber beam loss monitor based on Cerenkov principle

Chang LIU,Yongbin LENG,Luyang YU,Weimin ZHOU

2013-01-01

Abstract:Background: A new type of beam loss monitor (BLM) system is needed in the synchrotron radiation light source or FEL facility to monitor the real-time beam loss inside the small-gap insertion devices. Purpose: A BLM system was developed with optical fiber as the probe to meet the requirements of SSRF. Methods: The whole system consists of a 30-m long step-index fiber, photomultiplier tubes (PMT), a 10-bit 8-GS/s high-speed waveform digitizer and a PXI input-output controller. The software was developed under the Linux system based on Experimental Physics and Industrial Control System (EPICS). A new measurement and corresponding calculation method were designed to make the system work well with the multi-bunch operation mode in the storage ring of SSRF. Results: The BLM system worked well at SSRF. And the results of beam experiments showed that the system could detect beam loss properly even at the 1-mA low current case. Conclusions: This system could be used in the detection of beam loss dose and position. In the experiments the counts of light pulses can be used as a rough estimation of beam loss dose. The noise floor is about 3.56% of the total count in the 220-mA top-up user operation mode.
Beam Instrumentation and Diagnostics

Peter Forck

DOI: https://doi.org/10.48550/arXiv.2009.10411

2020-09-22

Abstract:The determination of beam parameters is essential for the operation and development of any accelerator facility. The working principle of frequently used beam instruments for electron and proton beams is discussed. The article comprises of the beam instrumentation for beam current determination, the usage of beam position monitors for bunched beams, methods for transverse profile and emittance diagnostics, bunch shape measurement and the usage of beam loss monitors.

Accelerator Physics,Instrumentation and Detectors
The beam loss monitoring system for HLS storage ring

Li Yuxiong,Cui Yonggang,Li Weimin,Li Juexin,Liu Zuping,Shao Beibei

DOI: https://doi.org/10.1016/S0168-9002(01)00252-2

2001-01-01

Abstract:A beam loss monitoring system has been established at HLS. This paper gives its principle and scientific grounds. Study on the ring's TBA structure and utilization of Monte-Carlo calculation to the shower electrons is important in its design. The system composition and performance are also introduced. The detector BLMs, data acquisition devices and host PC are linked via CAN bus. This system is helpful to analyze beam loss distribution and regulate the machine operation parameters.
Detection of Equipment Faults Before Beam Loss

J. Galambos

DOI: https://doi.org/10.5170/CERN-2016-002.253

2016-08-09

Abstract:High-power hadron accelerators have strict limits on fractional beam loss. In principle, once a high-quality beam is set up in an acceptable state, beam loss should remain steady. However, in practice, there are many trips in operational machines, owing to excessive beam loss. This paper deals with monitoring equipment health to identify precursor signals that indicate an issue with equipment that will lead to unacceptable beam loss. To this end, a variety of equipment and beam signal measurements are described. In particular, several operational examples from the Spallation Neutron Source (SNS) of deteriorating equipment functionality leading to beam loss are reported.

Accelerator Physics
Beam Loss Monitoring with Fixed and Translating Scintillation Detectors Along the Fermilab Drift-tube Linac

J. Stanton,R. Sharankova,K. Seiya,M. Wesley

2023-05-24

Abstract:The Fermilab Linac is a roughly 145 meter linear accelerator that accelerates H- beam from 750 keV to 400 MeV and provides beam for the Booster and the rest of the accelerator chain. The first section of the Linac is a Drift-Tube Linac (DTL), which in its current state, suffers from a lack of instrumentation along its length. As a result, operational staff do not have access to the diagnostic information needed to tune the critical components of this accelerator, such as the quadrupole magnets within the drift tubes. This work presents an effort to utilize both fixed and translating scintillation detectors to investigate beam loss along the first two cavities of the DTL.

Accelerator Physics
Beam Loss in Linacs

M.A. Plum

DOI: https://doi.org/10.5170/CERN-2016-002.39

2016-08-08

Abstract:Beam loss is a critical issue in high-intensity accelerators, and much effort is expended during both the design and operation phases to minimize the loss and to keep it to manageable levels. As new accelerators become ever more powerful, beam loss becomes even more critical. Linacs for H- ion beams, such as the one at the Oak Ridge Spallation Neutron Source, have many more loss mechanisms compared to H+ (proton) linacs, such as the one being designed for the European Spallation Neutron Source. Interesting H- beam loss mechanisms include residual gas stripping, H+ capture and acceleration, field stripping, black-body radiation and the recently discovered intra-beam stripping mechanism. Beam halo formation, and ion source or RF turn on/off transients, are examples of beam loss mechanisms that are common for both H+ and H- accelerators. Machine protection systems play an important role in limiting the beam loss.

Accelerator Physics
Performance assessment of a newly developed non-invasive 2D beam profile monitor for high-intensity accelerators

Sherry Rosily,Hari Prasad M,Biswaranjan Dikshit,Srinivas Krishnagopal,Rajesh Kumar

DOI: https://doi.org/10.1088/1748-0221/19/06/p06001

2024-06-05

Journal of Instrumentation

Abstract:In high-intensity accelerators, minimizing beam loss is paramount to avoid damages and activation of accelerator components. To achieve this, a reliable beam profile monitor is essential for assessing the beam center and spread. Additionally, the beam profile can be used to steer the beam during regular operation, thus reducing beam loss. In cases of irregular events, the monitor can initiate beam profile recording to identify and address any issues promptly. In this manuscript, we present a detailed description of a non-invasive 2D beam profile monitor, focusing on its components, operation, and most importantly, its reliability and failure modes. From operation experience, failure modes of the system and its effects were identified. Fault tree analysis was carried out. Failure rate of sheet generator was estimated using response surface method. Failure rates of components were used to estimate the failure rate of the system. From the target reliability, the required maximum repair time of the system was calculated.

instruments & instrumentation
Introduction to Beam Instrumentation and Diagnostics

M. Gasior,R. Jones,T. Lefevre,H. Schmickler,K. Wittenburg

DOI: https://doi.org/10.5170/CERN-2014-009.23

2016-01-19

Abstract:These lectures aim to describe instruments and methods used for measuring beam parameters in particle accelerators. Emphasis will be given to new detection and analysis techniques in each field of accelerator instrumentation. A clear distinction is made between 'instrumentation', the design and construction of the instruments themselves, and 'diagnostics', the use of the data from these instruments for running and improving the performance of the accelerator.

Accelerator Physics
Beam loss measurement system for energy calibration

Zhongtao Lu,Yucong Sun,Jieqin Lan,Hongliang Xu

DOI: https://doi.org/10.3788/HPLPB20132508.2071

2013-01-01

Abstract:In order to measure beam energy in Hefei Light Source accurately, a new set of precise and sensitive beam loss measurement system is built, and a kind of plastic scintillator detector which has high detection efficiency for low energy photons is adopted. According to the measured signal of beam loss, a set of digital signal processing circuit is developed. The experimental results show that the beam loss measurement system meets the requirements of the spin resonant depolarization method and can obtain the change of the beam loss accurately and sensitively. The measuring principle and theoretical basis of spin resonant depolarization is also introduced.
The Radiation Measurement Applied to Beam Lifetime Study on the Synchrotron Radiation Facilities

YX Li,JX Li,ZP Liu,YG Cui,GH Gong,BB Shao

DOI: https://doi.org/10.1016/s0168-9002(03)01098-2

2003-01-01

Abstract:To collect beam loss information from an accelerator radiation field is helpful to machine study and operation. For a synchrotron radiation storage ring, shower electrons give a distinct clue to loss location and a BLM-XS model detector is suitable to detect them. Recently, we set up a new beam loss monitoring system by this method for National Synchrotron Radiation Laboratory (NSRL) storage ring. It does not interfere with the vacuum chamber and machine operation. Different from other systems, the detectors are used in pairs, fixed on opposite sides of the chamber separately. Some interesting phenomena about beam lifetime were observed. We located exactly where an excessive beam loss took place during ramping process and solved the problem. It was proved that gas accumulated at the front ends of photo-beam lines strongly impacted the electron beam and led to beam lifetime decreases. The cause of beam lifetime decrease because of superconducting wiggler is discussed.
Several Physical Problems in the Beam Loss Monitoring System for HLS Storage Ring at NSRL

崔永刚,李裕熊,邵贝贝,李珏忻,李为民

DOI: https://doi.org/10.3321/j.issn:0253-3219.2002.02.004

2002-01-01

Abstract:The electrons lost from the storage ring beam produce a shower of particles when striking the vacuum chamber, and the beam losses can be probed by detecting the shower electrons distributed on the surface of beam pipe. Based on this principle, a new Beam Loss Monitoring System (BLM System) was designed and installed during the upgrading of accelerator in NSRL. In this paper, the selection of BLM detectors, the position to install them, and also the structure of BLM system were discussed in detail.
Monitoring System Experiments on Beam Loss at SSRF Injector

Jun Cai,XiaoBin Xia,XunJiang Xu,Xin Liu,JiaQiang Xu,GuangHong Wang,Ming Zeng

DOI: https://doi.org/10.1007/s11433-011-4520-9

2011-01-01

Abstract:Experiments on beam loss by using beam loss monitoring (BLM) system were carried out at Shanghai Synchrotron Radiation Facility (SSRF) injector. This system used highly sensitive and current-integrated Si-photodiode detectors and an Ethernet data acquisition (DAQ) system. The experimental results demonstrate that the Si-photodiode detectors are a useful tool that provides dynamic information on beam loss and investigates problems of machine operation. It also shows that the Si-photodiode BLM system is suitable for pulse-radiation of high-energy accelerators.
Design of the beam loss monitoring system in strong prompt radiation field

Li Juexin,Li Yuxiong,Li Weimin,Gong Guanghua,Zhao Zhengguo

DOI: https://doi.org/10.1016/j.nima.2007.04.098

2007-01-01

Abstract:It is inescapable that some electrons will be lost when they are accelerated or transported in the accelerator vacuum chamber. A beam loss monitoring (BLM) system, which works by the radiation measurement, has been successfully installed on the storage ring. Next on the schedule is design of the BLM system for LINAC and transport line. The radiation field around the LINAC and transport line consists of a strong prompt mixed (gamma, neutron) one. Its duty factor is only 10(-6) at Hefei Light Source (HLS). A detector based on counting cannot be used here, while one based on integral charge may be suitable in such a field. The most effective detected objects for estimating beam loss by radiation measurement are shower electrons because they can indicate the beam loss position more clearly than gamma rays. The detector also should have the ability to decrease stray radiation influence in strong prompt radiation field. For the requirements mentioned above, a new kind of photodiode detector is being developed. We analyzed the beam transportation process and calculated relevant parameters. Then the positions where the detectors should be fixed were determined. The CAN bus mode we use for the storage ring BLM system is out of date because of the rapid development in the communication field. TCP/IP communication is used for the new system. (c) 2007 Elsevier B.V. All rights reserved.
Beam Loss Monitor System for SSRF Storage Ring

guanghua gong,ming zeng,lei hou,beibei shao,yuxiong li

DOI: https://doi.org/10.1080/00223131.2008.10875880

IF: 1.126

2014-01-01

Journal of Nuclear Science and Technology

Abstract:A Beam Loss Monitor (BLM) system has been designed for Shanghai Synchrotron Radiation Facility (SSRF). The BLM system is utilized to detect beam loss around the electron storage ring. It will be helpful to find out the position of vacuum leakage, regulate the machine operation parameters, and study the beam lifetime. This paper will discuss some considerations in the BLM system design, including the detector selection, the beam loss mechanism, the detector location along the ring, and the structure of BLM system.
A Real-Time Beam Loss Monitoring System for Storage Ring of Ssrf

Cai Jun,Xu Xunjiang,Xia Xiaobin,Hou Lei,Zeng Ming,Wang Jianhua,Wang Guanghong,Liu Xin,Xu Jiaqiang

DOI: https://doi.org/10.13538/j.1001-8042/nst.22.5-8

2011-01-01

Abstract:In this paper we report the real-time beam loss monitoring (BLM) system at the storage ring of SSRF. The BLM-XS detectors and Ethernet data acquisition system are used in this system. Some applications and experiments of the BLM system are also presented. The BLM system provides dynamic information of beam loss for the storage ring, and is helpful to ensure the facility commissioning, investigate the problems of machine, optimize the machine parameters and further increase the beam lifetime.
Beam loss detection based on generation of Cherenkov light in optical fibers in the CERN Linear Electron Accelerator for Research

S. Benítez,B. Salvachúa,M. Chen

DOI: https://doi.org/10.1103/physrevaccelbeams.27.052901

2024-05-29

Physical Review Accelerators and Beams

Abstract:Cherenkov optical beam loss monitors (oBLMs) based on optical fibers are a revolutionary achievement among the monitoring systems in particle accelerators. Due to the nature of the Cherenkov phenomenon and the intrinsic characteristics of optical fibers, the photon production and fiber light transmission need to be studied to deduce the total amount of Cherenkov photons detected by the photosensors attached at the end of the system. Simulations of the Cherenkov oBLM detector system have been implemented using the fluka software with postprocessing considering the light attenuation and capture factors in the optical fiber. In addition, the study includes the longitudinal beam loss localization of the controlled beam losses produced along the CERN Linear Electron Accelerator for Research (CLEAR) test facility line. In this paper, the Cherenkov photon detection by an oBLM installed in the CLEAR facility is simulated, analyzed, and compared with experimental data. https://doi.org/10.1103/PhysRevAccelBeams.27.052901 Published by the American Physical Society under the terms of the Creative Commons Attribution 4.0 International license. Further distribution of this work must maintain attribution to the author(s) and the published article's title, journal citation, and DOI. Published by the American Physical Society

physics, particles & fields, nuclear
Beam-Induced Damage Mechanisms and their Calculation

A. Bertarelli

DOI: https://doi.org/10.5170/CERN-2016-002.159

2016-08-10

Abstract:The rapid interaction of highly energetic particle beams with matter induces dynamic responses in the impacted component. If the beam pulse is sufficiently intense, extreme conditions can be reached, such as very high pressures, changes of material density, phase transitions, intense stress waves, material fragmentation and explosions. Even at lower intensities and longer time-scales, significant effects may be induced, such as vibrations, large oscillations, and permanent deformation of the impacted components. These lectures provide an introduction to the mechanisms that govern the thermomechanical phenomena induced by the interaction between particle beams and solids and to the analytical and numerical methods that are available for assessing the response of impacted components. An overview of the design principles of such devices is also provided, along with descriptions of material selection guidelines and the experimental tests that are required to validate materials and components exposed to interactions with energetic particle beams.

Accelerator Physics
Recent Developments Of Beam Diagnostics

SUN Bao-Gen,LUO Qing,WANG Xiao-Hui

IF: 2.944

2008-01-01

Chinese Physics C

Abstract:The paper introduces some of the recent developments in beam diagnostics, which include the beam position measurement techniques with sub-micrometer resolution, the beam size measurement techniques with sub-micrometer resolution, and the bunch length measurement techniques with sub-picosecond resolution. The cavity beam position monitor and the digital BPM signal processing technique are introduced for the beam position measurement techniques. The laser wire beam profile monitor, and the optical transition radiation/optical diffraction radiation beam size monitor are introduced for the beam size measurement techniques. The spectral techniques of coherent radiation, the transverse deflecting cavity, the rf zero-phasing technique, and the electro-optic techniques axe introduced for the bunch length measurement techniques.
BPM Systems: A brief Introduction to Beam Position Monitoring

M. Wendt

DOI: https://doi.org/10.48550/arXiv.2005.14081

2020-05-28

Abstract:This introduction on beam position monitors (BPM) summarizes the fundamental parts of the tutorial presented at the CAS 2018 on beam instrumentation. The focus is on the signal detection and normalization, and on the principle of operation of commonly used broadband pickups, i.e.\ button and stripline BPMs. Other BPM types, such as split-plane and cavity BPMs are also discussed, as well as the detection of low-$\beta$ beams. Finally, a note on BPM signal processing techniques is given.

Accelerator Physics,Instrumentation and Detectors
Resolving Two Beams in Beam Splitters with a Beam Position Monitor

Sergey Kurennoy

DOI: https://doi.org/10.48550/arXiv.physics/0205066

2002-05-24

Abstract:The beam transport system for the Advanced Hydrotest Facility (AHF) anticipates multiple beam splitters [1]. Monitoring two separated beams in a common beam pipe in the splitter sections imposes certain requirements on diagnostics for these sections. In this note we explore a two-beam system in a generic beam monitor and study the feasibility of resolving the positions of the two beams with a single diagnostic device.

Accelerator Physics

Beam Loss Monitors

Development of fiber beam loss monitor based on Cerenkov principle

Beam Instrumentation and Diagnostics

The beam loss monitoring system for HLS storage ring

Detection of Equipment Faults Before Beam Loss

Beam Loss Monitoring with Fixed and Translating Scintillation Detectors Along the Fermilab Drift-tube Linac

Beam Loss in Linacs

Performance assessment of a newly developed non-invasive 2D beam profile monitor for high-intensity accelerators

Introduction to Beam Instrumentation and Diagnostics

Beam loss measurement system for energy calibration

The Radiation Measurement Applied to Beam Lifetime Study on the Synchrotron Radiation Facilities

Several Physical Problems in the Beam Loss Monitoring System for HLS Storage Ring at NSRL

Monitoring System Experiments on Beam Loss at SSRF Injector

Design of the beam loss monitoring system in strong prompt radiation field

Beam Loss Monitor System for SSRF Storage Ring

A Real-Time Beam Loss Monitoring System for Storage Ring of Ssrf

Beam loss detection based on generation of Cherenkov light in optical fibers in the CERN Linear Electron Accelerator for Research

Beam-Induced Damage Mechanisms and their Calculation

Recent Developments Of Beam Diagnostics

BPM Systems: A brief Introduction to Beam Position Monitoring

Resolving Two Beams in Beam Splitters with a Beam Position Monitor