Abstract:A special treatment of platinum group metals (PGMs) leaching from spent automotive catalyst is shown in this paper. Leaching of crushing and grinding automotive catalyst scrap in hydrochloric acid with defined concentration, added nitric acid as oxidant, produced chloride solution of the platinum group metals, while catalyst substrate (Al 2 O 3) remained indissoluble. Cementation of the leached platinum group metals from solution was made by powered aluminum with suitable pH values. The precipitate obtained by cementation with Al-powder is mixture of the platinum group metals and surplus aluminum. The surplus aluminum can be removed by selected resolving with hydrochloric acid. The mixture of platinum group metals (Pt, Pd, and Rh) is obtained by this treatment. Separation between platinum group metals was done by well-known chemical processes. 1. INTRODUCTION Automotive catalysts have been extensively used for reducing the amount of unburned hydrocarbons (HC), carbon monoxide (CO), and nitrogen oxides (NO x) from the exhaust gas emitted by automobiles. Platinum group metals (PGMs) have been used as catalytic agents because of their heat resistance and special catalytic activity. The content of total PGMs in automotive catalyst is about 0.5 to 2.0 g per kilogram. Autocatalyst essentially comprise a refractory oxide carrier on which two or more precious metals are dispersed in very low concentration. The worldwide demand of PGMs used for autocatalysts has increased with rapid motorization and the enforcement of stringent regulations for exhaust gas. In 2001, 37% of the worldwide demand for platinum, 72% of palladium and 85% of rhodium was for their use as automotive catalysts. In the year 2003, the overall demand of platinum was about 200 metric tons; 5% had to be met from stock in the last years because of lower primary and secondary production. Half of the produced platinum was used for catalysts in the automotive industry. From this, one third is covered by platinum out of secondary metallurgical processes [1,2]. Due to their scarcity and high price, the recovery of PGMs from spent automotive catalyst, generally called catalyst scrap, is a very important. The catalyst scrap generally consists of the surface layer with a high degree of porosity and the catalyst substrate (such as SiO 2 , Al 2 O 3 and CeO 2) with honeycomb structure. Ceramic materials were chosen for the initial monolith and they still dominate market. The preferred materials is called cordierite (synthetic cordierite has a composition approximating 2MgO, …

Iron capture mechanism for harmless recovering platinum group metals from spent automobile catalyst

Slag design and optimization for iron capturing platinum group metals from alumina-based spent catalysts

Optimization of synergistic capturing platinum group metals by Fe-Sn and its mechanism

Co-treatment of spent automotive catalyst and copper-bearing electroplating sludge to alloy platinum group metals with base metal matrices

Extraction of PGMs from insoluble Fe-Si-PGMs alloy by combined thermochemical and mechanochemical leaching: Sustainable, efficient, and scalable

Mechanism of PGMs capture from spent automobile catalyst by copper from waste printed circuit boards with simultaneous pollutants transformation

Recovery of platinum and synthesis of glass–ceramic from spent automotive catalyst via co-treatment process with coal fly ash

A novel method for efficiently recycling platinum group metals and copper by Co-smelting spent automobile catalysts with waste-printed circuit boards

Enrichment of Platinum Group Metals from Spent Automotive Catalyst Leaching Residue by a Combined Smelting and Wet Extraction Method

Recovery of valuable metals from electroplating sludge with reducing additives via vitrification

Efficient enrichment of platinum group metals from spent automotive catalysts by alkaline hydrothermal treatment and the subsequent acid leaching method

Extraction of platinum group metals from catalytic converters

Recovery of Platinum Group Metals from Spent Automotive Catalyst

A Selective Separation of Platinum Group Metals from the Fe-PGM Alloy Using Electrodeposition Combined with Electrochemical Dealloying

Recovery of platinum-group metals from spent catalysts by microwave smelting

Recovery of platinum group metals from aqueous solution by iron-electrocoagulation

Selective Recovery of Platinum Group Metals from Spent Automotive Catalysts by Leaching and Solvent Extraction

Synchronous extraction of Pt, Zr and Ce from spent catalysts via SoG-Si scraps melting collection by regulating Si reduction based on a new fluorine-containing slag

Single-Step Hydrometallurgical Method for the Platinum Group Metals Leaching from Commercial Spent Automotive Catalysts

Recovery of platinum from spent automotive catalyst based on hydrometallurgy

Precious metals recovery from aqueous solutions using a new adsorbent material