Abstract:In the classical planar heterojunction perovskite solar cells (PSCs), the electron conducting TiO2 layer shows lower conductivity than the hole transporting materials such as spiro-OMeTAD, which becomes one of the key problems in improving the power conversion efficiency (PCE) of PSCs. In this study, the surface of compact TiO2 layer is modified by a thin self-assembled dodecanedioic acid (DDDA) molecular layer. The TiO2 substrates are immersed into the DDDA solution for 0.5, 2.5, 4.5, 22 h, respectively. It is found that the PCE of PSCs is improved when using the DDDA modified TiO2, showing optimized PCE of 15.35% +/- 0.75% under AM 1.5G illumination at 100 mW.cm(-2) after 4.5 h modification. The short current density (J(SC)) of the best device is improved from 20.34 mA.cm(-2) to 23.28 mA.cm(-2), with the PCE increasing from 14.17% to 15.92%. And it is found that the hysteresis of the PSC is also reduced remarkably with hysteresis index decreasing from 0.4288 to 0.2430. In the meantime, the device with DDDA modification shows a significant improvement in light stability, keeping 71% of its initial PCE value after 720 min exposure under AM 1.5G illumination at 100 mW.cm(-2) without encapsulation. As a contrast, the device without DDDA modification keeps 59% of its initial PCE value under the same condition. To reveal the mechanism, we investigate the surface energy level change using ultraviolet photoemission spectroscopy. It is found that after DDDA modification, the valence-band maximum energy (E-VBM) of TiO2 decreases from -25 eV to -32 eV, and the conduction-band minimum energy (E-CBM) of TiO2 from -05 eV to -12 eV. The shifting of energy level optimizes the energy level alignment at the interface between the TiO2 and perovskite. It promotes the transport of electrons from perovskite layer to compact TiO2 layer and obstructs the transport of holes from perovskite layer to compact TiO2 layer more effectively. In addition, the decrease of E-CBM implies the increase of conductivity of TiO2. We further design a series of electrical experiments, and confirm that the modification improves the conductivity of TiO2 obviously with both contact resistance and thin-film resistance decreasing. In summary, our results indicate the enormous potential of the compact TiO2 layer with a thin self-assembled DDDA molecular layer modification to construct efficient and stable planar heterojunction PSCs for practical applications.

TiO2 modification with multi-acid treatment for efficient interfacial perovskite-TiO2 electron transport

Surface Modification of TiO2 for Perovskite Solar Cells

Synergistic Effects of the Physical Modification and Chemical Passivation Enabling Efficient Perovskite Solar Cells

Low‐Temperature in Situ Amino Functionalization of TiO2 Nanoparticles Sharpens Electron Management Achieving over 21% Efficient Planar Perovskite Solar Cells

Charge transfer enhancement of TiO2/perovskite interface in perovskite solar cells

Interface Modification by Ammonium Sulfamate for High‐Efficiency and Stable Perovskite Solar Cells

Interfacial Crosslinking for Efficient and Stable Planar TiO2 Perovskite Solar Cells

Enhancing Interface Interaction through Multifunctional Trisodium Citrate Modification of Electron Transport Layer in Fully Air‐Processed Perovskite Solar Cells

Improving the Electron Transport Performance of TiO2 Film by Regulating TiCl4 Post‐Treatment for High‐Efficiency Carbon‐Based Perovskite Solar Cells

Interface modification by formamidine acetate for efficient perovskite solar cells

Reconfiguration toward Self‐Assembled Monolayer Passivation for High‐Performance Perovskite Solar Cells

Improving The Tio2 Electron Transport Layer In Perovskite Solar Cells Using Acetylacetonate-Based Additives

Frontispiz: Unconventional Route to Oxygen‐Vacancy‐Enabled Highly Efficient Electron Extraction and Transport in Perovskite Solar Cells

Interfacial Energy Level Alignment and Defect Passivation by Using a Multifunctional Molecular for Efficient and Stable Perovskite Solar Cells

Improvement of current characteristic of perovskite solar cells using dodecanedioic acid modified TiO2 electron transporting layer

Modification of SnO2 by Acidic FAAc-HI Solution for Efficient and Stable Perovskite Solar Cells with a Multifunctional Interface

In Situ Surface Fluorination of TiO 2 Nanocrystals Reinforces Interface Binding of Perovskite Layer for Highly Efficient Solar Cells with Dramatically Enhanced Ultraviolet‐Light Stability

Efficient and stable perovskite solar cells by interface engineering at the interface of electron transport layer/perovskite

Interface engineering at electron transport/perovskite layers using wetting mesoporous titanium dioxide to fabricate efficient and stable perovskite solar cells

Energy Level Modulation of TiO2 Using Amino Trimethylene Phosphonic Acid for Efficient Perovskite Solar Cells with Average VOC of 1.19 V

The Application of Al2tio5 at the Tio2/Perovskite Interface to Decrease Carrier Losses in Solar Cells