Abstract:In order to promote the application of LIBS technology in electrolytic aluminum industry, give full play to its advantages of rapidness, no preparation and multi-element simultaneous detection. The contents of Fe and Si elements in general aluminium procuced from electrolysis process were detected by means of laser induced breakdown for the first time, and the reasonable experimental conditions were explored, the calibration curves were established and the content of Fe and Si in general aluminium were quantitatively analyzed based on reasonable experimental conditions. The accuracy of LIBS measurement results were examined according to national standard GB / T 7999-2015 "optical emission spectrometric analysis method of aluminum and aluminum alloy". The fundamental frequency 1 064 nm laser produced by Nd : YAG pulsed laser device as the excitation source producing plasma, the spectral informations were detected and recorded by multi-channel grating spectrometer and ICCD detector. First of all, LIBS spectral line was detected and the spectral line was assigned, the line of Al I 266. 04 nm, Si I 288. 15 nm and Fe I 259. 92 nm were selected for quantitative analysis through comprehensive consideration. The influence of trigger delay time, 1Q delay time, laser setting voltage on the spectral signal intensity and SNR were researched respectively in the paper. The experimental results show that the trigger delay time of 4 mu s, 1Q delay time of 170 similar to 190 is, the laser set voltage of 560 V are the reasonable experimental parameters for Si and Fe element quantitative analysis in this paper. According to the relationship between spectral intensity and elemental concentration, the calibration curves were cestablished by the internal standard method. The correlation coefficients were 0. 952 11 and 0. 919 72, and the relative standard deviation were 6. 34% and 7. 25% for Fe and Si elements respectively. There was a good linear relationship between concentration and spectral intensity, and the 12 samples were quantitatively analyzed base on the above model. The relative error of Fe content is 0 similar to 17. 3% and the relative error of Si content is 0 similar to 14. 3% compared with the results obtained by OES. The measurement results 100% comply with the allowable requirements for Si content in 12 samples, and the results 91. 7% meet the allowable difference requirements according to national atandard GB/T 7999-2015 "optical emission spectrometric analysis method of aluminum and aluminum alloy". The experimental results show that, LIBS technology has a certain value of promotion and using in the electrolytic aluminum industry for Fe and Si elements detection.

Improved Elemental Analysis of Laterite by Calibration-Free Laser Induced Breakdown Spectroscopy (CF-LIBS) Using Escape Factor Based Self-Absorption Correction

Multi-element Saha Boltzmann Plot (MESBP) coupled calibration-free laser-induced breakdown spectroscopy (CF-LIBS): An efficient approach for quantitative elemental analysis

A Method for Improving the Accuracy of Calibration-Free Laser-Induced Breakdown Spectroscopy by Exploiting Self-Absorption.

Quantitative Elemental Analysis of High Silica Bauxite Using Calibration-Free Laser-Induced Breakdown Spectroscopy.

Quantitative Analysis method of laser-induced breakdown spectroscopy based on temperature iterative correction of self-absorption effect

Analytical Techniques for Elemental Analysis: LIBS, LA-TOF-MS, EDX, PIXE, and XRF: A Review

Laser-Induced Breakdown Spectroscopy Applied to the Quantification of K, Ca, Mg and Mn Nutrients in Organo-Mineral, Mineral P Fertilizers and Rock Fertilizers

Accurate quantitative CF-LIBS analysis of both major and minor elements in alloys via iterative correction of plasma temperature and spectral intensity

Correction of Self-Absorption Effect in Calibration-Free Laser-Induced Breakdown Spectroscopy (CF-LIBS) with Blackbody Radiation Reference.

Self-absorption Correction Method for One-Point Calibration Laser-Induced Breakdown Spectroscopy.

Accuracy improvement of quantitative analysis in spatially resolved fiber-optic laser-induced breakdown spectroscopy

Laser-induced breakdown spectroscopy for rapid and accurate qualitative analysis of elemental composition in fertilizers

Parametric Study of Spot Size and Multi-Elemental Quantification of Geomaterials under Complex Matrix Conditions Using Fiber-Optic Laser-Induced Breakdown Spectroscopy

A numerical procedure for understanding the self-absorption effects in laser induced breakdown spectroscopy

Accuracy Improvement of Single-Sample Calibration Laser-Induced Breakdown Spectroscopy with Self-Absorption Correction

Investigation of the Self-Absorption Temporal Evolution of Alkali and Alkaline Earth Metal Elements in Soil Using Laser-Induced Breakdown Spectroscopy

Laser-Induced Breakdown Spectroscopy for Simultaneous Quantitative Analysis of Multi-Elements in Soil

Multi-element Analysis of Heavy Metal Content in Soils Using Laser-Induced Breakdown Spectroscopy: A Case Study in Eastern China

Response Surface Methodology for Optimizing LIBS Testing Parameters: A Case to Conduct the Elemental Contents Analysis in Soil

Progress in the Correction of Self-Absorption Effect on Laser-Induced Breakdown Spectroscopy

Investigation on Experimental Conditions and Quantitative Analysis for Fe and Si Elements in General Aluminum by Laser Induced Breakdown Spectroscopy Technique