Abstract:Power conversion efficiency (PCE) of organic solar cells (OSCs) has reached the threshold for application. However, the high PCEs are mostly obtained from the small‐area OSCs processed by the halogenated solvent, such as chloroform (CF), because the high‐performance A‐DA'D‐A type small molecule acceptors (SMAs) need the CF processing for suitable solubility and rapid solvent evaporation to get appropriate aggregation morphology. Herein, we synthesized two new A‐DA'D‐A type SMAs of Y6‐Ph and L8‐Ph by introducing a phenyl end group in the branched alkyl inner side chains of the representative SMAs Y6 and L8‐BO respectively, for overcoming the excessive aggregation of SMAs in the long‐time film‐forming process in the nonhalogenated solvent processing. Firstly, we studied the effect of the processing solvent boiling point on the aggregation property and photovoltaic performance of the four SMAs of Y6, L8‐BO, Y6‐Ph and L8‐Ph, by using the most commonly used halogenated processing solvents: low‐boiling‐point CF (rapid film forming process) and high‐boiling‐point chlorobenzene (CB) (slow film forming process) for device fabrication of the OSCs with PM6 as polymer donor. It was found that the Y6‐ and L8‐BO‐based OSCs exhibit a dramatic drop in PCEs from CF‐ to CB‐processed devices owing to the large phase separation in the CB‐processed OSCs. On the contrary, the devices based on Y6‐Ph and L8‐Ph with the phenyl ending inner side chains show obviously increased PCEs for the OSCs processed by high‐boiling‐point CB. The L8‐Ph‐based devices processed by CB demonstrated an PCE of 18.83% with a high FF of 80.55%, which is even better than the L8‐BO‐based OSCs processed by CF. Furthermore, the L8‐Ph‐based OSCs processed by nonhalogenated solvent o‐xylene (o‐XY) also achieved a high PCE of 18.40% with an FF of 80.11%, which is the best‐performed OSC fabricated from the nonhalogenated solvents so far. In addition, the large‐area (1 cm2) OSCs based on PM6:L8‐Ph processed by o‐XY also demonstrated a higher PCE of 16.66%. The results indicate that introducing phenyl end group in the inner side chains is an effective strategy to improve photovoltaic performance of the A‐DA'D‐A SMAs for future application of the OSCs with nonhalogenated solvent processing. This article is protected by copyright. All rights reserved

A Difluoro‐Methoxylated Ending‐Group Asymmetric Small Molecule Acceptor Lead Efficient Binary Organic Photovoltaic Blend

Nonfullerene Small‐Molecule Acceptors for Organic Photovoltaics: Understanding the Impact of Methoxy Substitution Position on Molecular Packing and Electron‐Transfer Properties

Asymmetric Alkyl Chain Engineering for Efficient and Eco‐Friendly Organic Photovoltaic Cells

Achieving Balanced Charge Transport and Favorable Blend Morphology in Non-Fullerene Solar Cells Via Acceptor End Group Modification

Rebuilding Peripheral F, Cl, Br Footprints on Acceptors Enables Binary Organic Photovoltaic Efficiency Exceeding 19.7%

Balancing Intermolecular Interactions between Acceptors and Donor/Acceptor for Efficient Organic Photovoltaics

A 4‐arm Small Molecule Acceptor with High Photovoltaic Performance

Molecular Design of Fully Nonfused Acceptors for Efficient Organic Photovoltaic Cells

End-group modification of non-fullerene acceptors enables efficient organic solar cells

Introducing Phenyl End Group in The Inner Side Chains of A‐Da'd‐A Acceptors Enables High‐Efficiency Organic Solar Cells Processed with Nonhalogenated Solvent

A novel A-DA'D-A bifunctional small molecule for organic solar cells application with impressive photovoltaic performance

A Difluoro‐Monobromo End Group Enables High‐Performance Polymer Acceptor and Efficient All‐Polymer Solar Cells Processable with Green Solvent under Ambient Condition

Ending group modulation of asymmetric non-fullerene acceptors enables efficient green solvent processed organic solar cells

Small Molecule Acceptors with a Nonfused Architecture for High-Performance Organic Photovoltaics

Asymmetric Acceptors with Fluorine and Chlorine Substitution for Organic Solar Cells toward 16.83% Efficiency

Regio‐Regular Polymer Acceptors Enabled by Determined Fluorination on End Groups for All‐Polymer Solar Cells with 15.2 % Efficiency

Non‐Fused π‐Extension of Endcaps of Small Molecular Acceptors Enabling High‐Performance Organic Solar Cells

Medium bandgap A-DA'D-A type small molecule acceptors prepared by synergetic modification strategy for efficient indoor organic photovoltaic devices

20.2% Efficiency Organic Photovoltaics Employing a π‐Extension Quinoxaline‐Based Acceptor with Ordered Arrangement

Compromising Charge Generation and Recombination with Asymmetric Molecule for High‐Performance Binary Organic Photovoltaics with Over 18% Certified Efficiency

Dithienobenzothiadiazole-Bridged Nonfullerene Electron Acceptors for Efficient Organic Solar Cells