Abstract:The analysis of the crankshaft bearing condition of the automotive internal combustion engines in the case of insufficiency and breakage of oil supply to them is carried out. It is noted that this fault is one of the most common causes of damage to rubbing pairs in operation. At the same time, the different groups of bearings are often damaged, which cannot be explained within the framework of existing models of plain bearing lubrication. The objective of the work is to develop a mathematical model of oil supply to connecting rod bearings in emergency mode, taking into account the characteristic features of the bearing design. The model also, depending on the nature of the damage, should help to determine and explain the causes of bearing failures if they occur in different modes when operating conditions are broken. A computational model has been developed that makes it possible to assess the effect of design differences in the features of oil supply and the action of the centrifugal forces during crankshaft rotation on the oil column in the lubrication hole where oil is supplied to the conrod bearing. Calculations of the change in time of the oil supply pressure to the connecting rod bearings for the various designs of the crankshaft lubrication holes have been performed. It is shown that, depending on the operating mode of the engine and its design, the oil pressure in front of the connecting rod bearings does not disappear immediately after oil supply failure to crankshaft. Moreover, the lower the crankshaft speed is, the longer the lubrication of the conrod bearings will continue. The calculation results are confirmed by the data of the expert studies of the engine technical condition, in which the crankshaft was wedged in the damaged main bearings was found in the absence of serious damage to the connecting rod ones. It has been found that such features of the damage correspond to an rapid breakage of the oil supply to the crankshaft in the case of such operational damage as the oil pump and pressure reducing valve failure, the oil filter seal and oil pan destruction, etc. The developed model explains the difference in lubrication conditions and in the damage feature to the main and connecting rod bearings in the emergency cases of the oil supply breakage, which are observed during operation, and helps to clarify the failure causes. This makes it possible to use the model and the obtained data when providing auto technical expert studies of the failure causes of automobile internal combustion engines This makes it possible to use the model and the obtained data when providing auto technical expert studies of the failure causes of automobile internal combustion engines when the operating conditions are broken.

Oil-Flow through Crankshaft and Connecting-Rod Bearings

Engine Lubrication System for Oil Flow Reduction

CFD Simulation of Connecting Rod Bearing Lubrication

Experimental and Numerical Study of the Influence of Loading Direction on the Lubrication and Cooling of Self-Circulating Oil Bearing System Applied in Internal Gear Pumps

Lubrication Analysis of a Connecting-Rod Bearing in a High-Speed Engine. Part II: Lubrication Performance Evaluation for Non-Circular Bearings

Analysis of Oil-Air Two-Phase Flow Characteristics inside a Ball Bearing with Under-Race Lubrication

Experimental Investigation of Lubrication Oil Film Dynamics in a Typical Aero-Engine Bearing Chamber Environment

The influence of centrial forces on crankshaft bearing lubrication is in emergency modes of the engine of the car

Lubricant Shear Thinning Analysis of Engine Journal Bearings

A Computational Fluid Dynamics Simulation of Oil–Air Flow Between the Cage and Inner Race of an Aero-engine Bearing

Experimental and Numerical Analysis of a Self-Circulating Oil Bearing System for Gear Pumps

Research on the thermohydrodynamic lubrication performance of engine main bearing with rough surface considering the axial motion and deformation of crankshaft

An Efficient Journal Bearing Lubrication Analysis For Engine Crankshafts

Lubrication Conditions and Development of Pre-failure State of Crankshaft Bearings

Lubrication characteristics study of main bearings on crankshaft balance rate

The Effect of Crankshaft Flexibility on the EHL of Connecting Rod Bearings

A Study On the Oil Film Thickness Between the Lower Rail of Oil Control Ring and Lower Flank of Oil Control Ring Groove of an Engine

Small End Conrod Lubrication

Numerical Analyses of Hydrodynamic Lubrication and Dynamics of the Rolling Piston and Crankshaft in a Rotary Compressor

Theoretical and experimental evaluation of engine bearing performance