Abstract:Titanium matrix composites with TA15 alloy as the matrix and TiB (ranging from 0 to 4 vol%) as reinforcement were produced via powder metallurgy-based hot press sintering, employing AlB2 precursor. The addition of TiB to TA15 led to a substantial reduction in the colony and prior beta grain sizes, and an increase in the lath thickness in the composites. Plastic deformation due to planar slip, which traverses across the alpha/beta-ligament phase boundaries within each colony, may cause TiB particles located on colony boundaries to break, potentially more so than those within the colony. The composite containing 1 vol% TiB exhibited simultaneous improvements in strength, ductility, and strain hardening rate, attributed to colony refinement and possibly a sizable amount of intra-boundary TiB. Further increase in the TiB content led to significant drops in ductility, which was further exacerbated by the precipitation of alpha 2-Ti3Al phase. A substantial decrease in the mode I fracture toughness, attributed to reduced colony size and diminished crack deflection, was noted in the composite with 1 vol% TiB. The colony size refinement also contributed to a reduction in the threshold stress intensity factor range, Delta K0, for the fatigue crack growth, owing to the decreased tortuosity of the fatigue crack front. This study elucidates the intricate relationship between TiB location, microstructure, and mechanical properties, providing insights for the design of TiB-reinforced titanium alloys with both alpha and beta phases.

Mechanical responses of in-situ TiB2/7050 composite subjected to monotonic and cyclic loadings: A comparative study with 7050-Al

High Cycle Fatigue Behavior of the In-Situ TiB2/7050 Composite

High fatigue performance and microscopic mechanisms of in-situ TiB 2 /7050Al composite at different temperatures

Cyclic Deformation Behavior of in Situ Aluminum–matrix Composites of the System Al–Al3Ti–TiB2–Al2O3

Compressive response and microstructural evolution of in-situ TiB2 particle-reinforced 7075 aluminum matrix composite

Ductile Fracture Behavior of in Situ TiB2 Particle Reinforced 7075 Aluminum Matrix Composite in Various Stress States

Thermo⁻Mechanical Behavior and Constitutive Modeling of In Situ TiB2/7050 Al Metal Matrix Composites Over Wide Temperature and Strain Rate Ranges

Stress Corrosion Cracking Behavior of In-Situ TiB2/7050 Composite

Effects of three stress levels on the fatigue properties and fracture mechanisms of an in-situ synthesized TiB/Ti-6Al-4V titanium matrix composite

High Strain Rate Response of In-Situ TiB2/7055 Composite by Taylor Impact

Mechanical Properties and Strengthening Effects of in Situ (Tib+tic)/ti-1100 Composite at Elevated Temperatures

Investigation on the High-Temperature Ductility and Fracture Mechanisms of an In-Situ Particle Reinforced Al Matrix Composite 7075Al/tib2

Dynamic deformation behavior of a high reinforcement content TiB2/Al composite at high strain rates

Effects of Nanosized Particles on Microstructure and Mechanical Properties of an Aged In-Situ TiB2/Al-Cu-Li Composite

Deformation, Fracture, and Fatigue Crack Growth Behavior in TiB-reinforced Near-Α Ti Matrix Composites Fabricated Using Powder Metallurgy Technique

Experimental study of the mechanisms of nanoparticle influencing the fatigue crack growth in an in-situ TiB2/Al-Zn-Mg-Cu composite

Low-cycle Fatigue Behavior and Damage Progression of a Fiber Reinforced Titanium Matrix Composite

Tensile properties of 15wt. %TiB2/7055 composite fabricated by in-situ method

Fatigue Crack Initiation and Propagation in A356 Alloy Reinforced with in Situ TiB2 Particles

The dynamic mechanical response of Al2O3 and TiB2 particulate reinforced aluminum matrix composites produced by in-situ reaction

LOW CYCLE FATIGUE OF (Al2O3+TiB2+Al3Ti) /Al COMPOSITES FABRICATED BY REACTIVE HOT PRESSING