Abstract:Emerging organic solar cells based on a ternary strategy is one of the most effective methods for improving the blend film morphology, absorption ability, and device performances. On the other hand, this strategy has had very limited success in all-polymer solar cells (all-PSCs) because of the scarcity of new polymers and the challenges faced during third component optimization. Herein, highly efficient ternary all-PSCs were developed from siloxane-functionalized side chains with a wide-band-gap (Eg) polymer, Si-BDT, which is blended with a medium and ultra-narrow Eg polymer donor and acceptor, PTB7-Th, and DCNBT-TPIC. An impressive power conversion efficiency (PCE) of 13.45% was achieved in the ternary all-PSCs [PTB7-Th(0.6):Si-BDT(0.4):DCNBT-TPIC(0.6)] with the addition of 0.4 wt equivalent Si-BDT into binary all-PSCs [PTB7-Th(1):DCNBT-TPIC(0.6) PCE of 10.11%]. In contrast, the binary all-PSCs with a Si-BDT(1):DCNBT-TPIC(0.6) active layer only exhibited a good PCE of 9.92%. More importantly, the siloxane-functionalized side chains increase the light-absorption ability, carrier mobility, blend miscibility, and film morphology in ternary devices compared to those of the binary devices. Hence, exciton dissociation, charge carrier transport, and suppressed recombination properties were facilitated. In the presence of Si-BDT, both binary and ternary all-PSCs PCEs are significantly improved. Indeed, 13.45% PCE is one of the best values reported for all-PSCs except for those based on polymerized small molecule acceptors. In addition, the ternary all-PSCs showed excellent environmental and thermal stabilities with 95 and 84% of the initial PCE retained after 900 and 500 h, respectively. These results offer effective device engineering, providing a new avenue for improving the device performance in ternary all-PSCs.The Supporting Information is available free of charge at https://pubs.acs.org/doi/10.1021/acsami.1c20542.Additional text describing experimental details (materials and measurements and characterization of the all-PSCs), SCLC, UV–vis absorption spectra, UPS analysis, efficiency histograms, J–V curves, PL spectra, EDS element mapping, contact angle, GIXRD study, and recent publications based on ternary all-PSCs (PDF)This article has not yet been cited by other publications.

Two Y6 Derivations with Similar Chemical Structure As One Alloyed Acceptor Enable Efficient Ternary-Blend Polymer Solar Cells

Alloy-like ternary polymer solar cells with over 17.2% efficiency

High-Performance Ternary Polymer Solar Cells from A Structurally Similar Polymer Alloy

Two Compatible Acceptors As an Alloy Model with a Halogen-Free Solvent for Efficient Ternary Polymer Solar Cells

Ternary Polymer Solar Cells Based-on Two Polymer Donors with Similar HOMO Levels and an Organic Acceptor with Absorption Extending to 850 Nm

Improved Blend Film Morphology and Free Carrier Generation Provide a High-Performance Ternary Polymer Solar Cell

Efficient Non-Halogenated Solvent Processed Ternary All-Polymer Solar Cells with A Favorable Morphology Enabled by Two Well-Compatible Donors.

Wide Bandgap Perylene Diimide Derivatives as an Effective Third Component for Parallel Connected Ternary Blend Polymer Solar Cells

Two Compatible Nonfullerene Acceptors with Similar Structures As Alloy for Efficient Ternary Polymer Solar Cells

Improved Molecular Ordering in a Ternary Blend Enables All‐Polymer Solar Cells over 18% Efficiency

Enhanced Photovoltaic Performances Via Ternary Blend Strategy Employing a Medium-Bandgap D-A Type Alternating Copolymer As the Single Donor

A Simple-Structure Small-Molecule Acceptor Enables over 18% Efficiency Ternary Polymer Solar Cells with a Broad Composition Tolerance

Ternary Organic Photovoltaic Cells Exhibiting 17.59% Efficiency with Two Compatible Y6 Derivations as Acceptor

Ternary Polymer Solar Cells with High Efficiency of 14.24% by Integrating Two Well‐Complementary Nonfullerene Acceptors

Facile Strategy for Third Component Optimization in Wide-Band-Gap π-Conjugated Polymer Donor-Based Efficient Ternary All-Polymer Solar Cells

A chlorinated polymer promoted analogue co-donors for efficient ternary all-polymer solar cells

High Voc Ternary Nonfullerene Polymer Solar Cells with Improved Efficiency and Good Thermal Stability

Achieving High-Performance Ternary Organic Solar Cells through Tuning Acceptor Alloy.

Manipulating Polymer Backbone Configuration via Halogenated Asymmetric End-Groups Enables Over 18% Efficiency All-Polymer Solar Cells

Approaching 18% efficiency of ternary layer-by-layer polymer solar cells with alloyed acceptors

A Minimal Benzo[c][1,2,5]thiadiazole-Based Electron Acceptor As a Third Component Material for Ternary Polymer Solar Cells with Efficiencies Exceeding 16.0%