Abstract:Doped AlN thin films, especially high Sc-ratio AlScN film, have been reported to significantly improve the piezoelectric properties and draw attention for high performance resonators, transducers and integrated ferroelectric applications. However, many demonstrated devices were limited by poor film stress control, abnormal oriented grains and lack of a good etching profile. Compared to costly single alloy target, co-sputtered AlScN films can benefit customized doping concentrations and provide a unique solution for high Sc-ratio AlScN film quality and device studies. In this work, the optimized co-sputtering deposition and ICP etching processes of 500 nm AlScN thin film were developed and released AlScN Lamb-wave resonators were demonstrated. The influence of stress control by changing N2 process gas on the crystalline orientation, abnormal orientation grains, film roughness and piezoelectric property of AlScN thin films were discussed in detail. The AlScN film with a high Sc content requires a lower deposition pressure to obtain good crystalline quality. Al0.85Sc0.15N thin films with FWHM of 1.75°, an average stress of −14.5 MPa and a stress range of 156 MPa were obtained. 130 nm/min etching rate and 77° sidewall profile were achieved by optimized ICP etching of Al0.78Sc0.22N film. Lamb-wave resonators were fabricated based on both Al0.78Sc0.22N and Al0.85Sc0.15N thin films, achieving a quality factor of over 1000 at resonant frequency of approximately 300 MHz. The electromechanical coupling coefficients were improved by 152% and 80% compared to pure AlN devices.[2021-0210]

Improve the response frequency of epitaxial LiNbO3 film SAW devices by substrate strain gradient

Integration of epitaxial LiNbO3 thin films with silicon technology

High speed surface acoustic wave and laterally excited bulk wave resonator based on single-crystal non-polar AlN film

Theoretical and Experimental Study of High-Electromechanical-Coupling Surface Acoustic Wave Resonators Based on A-Plane (1120)al0.56sc0.44n Films

Homo-epitaxial growth of LiNbO3 thin films by Pulsed Laser deposition

Enhancement of piezoelectric response in V doped LiNbO3 films deposited by RF magnetron sputtering

Frequency Response Improvement of a Two-Port Surface Acoustic Wave Device Based on Epitaxial AlN Thin Film

Large Electromechanical Response in a Polycrystalline Alkali-Deficient (k,na)nbo3 Thin Film on Silicon.

Theoretical and experimental study of high electromechanical coupling SAW resonators based on a‐plane ( 11 2 ̄ 0 ) Al0.56Sc0.44N films

Surface acoustic wave devices fabricated on epitaxial AlN film

Effect of growth rate on the characteristics of LiNbO3 waveguide thin films on SiO2/Si substrate by PLD

Design of SAW Sensor for Longitudinal Strain Measurement with Improved Sensitivity

Theoretical Analysis of Surface Acoustic Wave Propagating Properties of Y-cut Nano Lithium Niobate Film on Silicon Dioxide

Surface Acoustic Wave Devices Based on High Quality Temperature-Compensated Substrates

High Quality Co-Sputtering AlScN Thin Films for Piezoelectric Lamb-Wave Resonators

GROWTH OF LITHIUM NIOBATE CRYSTAL BY THE VERTICAL BRIDGMAN METHOD

A Simulated Investigation of Lithium Niobate Orientation Effects on Standing Acoustic Waves

Effect of growth rate on the characteristics of LiNbO_3 waveguide thin films on SiO_2/Si substrate by PLD

Single-crystalline LiNbO 3 film based wideband SAW devices with spurious-free responses for future RF front-ends

Oxygen Pressure Dependent Growth of Pulsed Laser Deposited Linbo3 Films on Diamond for Surface Acoustic Wave Device Application

The Thin Film Bulk Acoustic Wave Resonator Based On Single-Crystalline 43 Degrees Y-Cut Lithium Niobate Thin Films