Abstract:Ni-Cr-Mo alloys are widely-used materials in various critical applications owing to their excellent balance of strength and ductility. The precipitates play a significant role in the exceptional mechanical properties of these alloys, yet the precise microscopic mechanisms underpinning the enhanced properties are still open. Here, the atomistic simulation based on molecular dynamics (MD) was employed to investigate the deformation behavior and mechanism of the precipitation-strengthened single crystal Ni-Cr-Mo alloy under uniaxial loading at temperatures of 300 K, 500 K, 700 K, and 900 K. The results revealed high temperature-induced softening under both tension and compression. Furthermore, the tension-compression asymmetry in ultimate strength is influenced by the disparity in Schmid factor of leading Shockley partial dislocations. By monitoring the evolution of microscopic defects during deformation, the Shockley partial dislocation slip was identified as the primary deformation mechanism in the plastic regime at 300 K, 500 K, 700 K, and 900 K. Based on that, a flow stress representation model was proposed. Moreover, the investigation on the nanoscale Ni 2 (Cr, Mo) precipitates revealed the transition from the Orowan bypass mechanism to the shearing mechanism under uniaxial loading, accompanied by the formation of dislocation tangles. The dislocation tangles impeded dislocation slip, enhancing the mechanical properties of the alloy. The precipitate can significantly promote the formation of the lamellar dislocation structure under compression at 900 K.

Influence of plastic deformation on the corrosion behavior of CrCoFeMnNi high entropy alloy

Influence of Cr on Microstructure and Electrochemical Properties of FeNiMnCuCrx High-entropy Alloy

Oxidation Behavior of CoCrFeMnNi High Entropy Alloy after Plastic Deformation

Corrosion Behavior of Ultrafine-Grained CoCrFeMnNi High-Entropy Alloys Fabricated by High-Pressure Torsion

Microstructure evolution and composition redistribution of FeCoNiCrMn high entropy alloy under extreme plastic deformation

Plastic deformation mechanism of CoCrxNi medium entropy alloys

The influence of microstructural evolutions on electrochemical corrosion and passive behavior in precipitation-strengthened high-entropy alloys

Effects of Nickel on the Microstructure, Mechanical properties and Corrosion Resistance of CoCrFeNixAl0.15Ti0.1 High Entropy Alloy

Cyclic plasticity and fatigue damage of CrMnFeCoNi high entropy alloy fabricated by laser powder-bed fusion

Influence of deformation on the structure and the mechanical properties of a high-entropy Fe25Cr20Ni20Co10Mn15Al10 alloy

The effect of Mn addition on corrosion behaviour of equiatomic CoCrFeNi high entropy alloys in NaCl solution

The deformation behavior and mechanism modeling of a corrosion-resistant Ni-Cr-Mo alloy with nanoscale precipitates at room and elevated temperatures

Anomalous dislocation response to deformation strain in CrFeCoNiPd high-entropy alloys with nanoscale chemical fluctuations

Creep behaviour and microstructural evolution of Al x CrMnFeCoNi high-entropy alloys

Dislocation evolution and induced precipitation on corrosion resistance of a novel Al-Mg-Zn-Er-Zr alloy during hot compression

Effect of potential difference in CoXCrNiMoCB high-entropy alloy coatings on corrosion resistance improvement

Effect of drawing deformation on microstructure and mechanical properties of Fe-Cr-Co-W alloy

From stacking fault to phase transformation: A quantitative model of plastic deformation of CoCrFeMnNi under different strain rates

Effects of pre-deformation on microstructure, mechanical properties and corrosion performance of an Al-Cu-Mg-Ag alloys

In-situ study of room temperature tensile deformation of a CrMnFeCoNi high-entropy alloy

Effect of microstructure evolution on wear resistance of equal molar CoCrFeNi high-entropy alloy