Abstract:During the past few decades, various organic aerogels (AGs) have been synthesized and shown a number of exceptional and even unique properties, such as low bulk density, high porosity, great surface areas, and extremely low thermal conductivity, which enable them being the focus of industry and academia. Thus, AGs exhibit substantial performance boosts in numerous applications such as adsorption, separation, catalysis, energy conversion and storage, and so on. Regrettably, AGs generally exhibit high cost, poor thermal and mechanical properties, which seriously restrict their large-scale applications. In this study, ceramic was introduced into commercial available resin derived aerogel due to the enhancement of silicon to thermal stability and low cost of the resin. Silica ceramic modified phenolic resin (PR-SiO2) aerogel was synthesized by a simple sol-gel polymerization of ceramic precursor, PR, hexamethylenetetramine in an ethylene glycol solution, followed by solvent exchange and ambient pressure drying. The modified effect on the porous structure, textural property, and thermal stability was studied by scanning electron microscope (SEM), nitrogen adsorption isotherms, and thermogravimetric analysis (TGA). According to the characterizations of SEM and nitrogen adsorption, the obtained PR-SiO2 hybrid aerogels have a continuous three dimensional network that consists of phenolic nano-particles and curved nano-sheets with size from 50 to 90 nm, which define numerous mesopores and macropores. TGA in argon atmosphere indicated that the thermal stability of the PR-SiO2 aerogels (both maximum decomposition rate and char yield at 1000 degrees C) is better than that of the pristine PR aerogel. In order to improve the mechanical properties, carbon fabric reinforced aerogel composite was prepared by impregnating carbon-bonded carbon fiber (CBCF) composite with the aerogels. In the micrographs of the aerogel matrix composite, the aerogels are fully and uniformly occupied the void between carbon fibers, and coated with a thin layer on the fiber surface. Moreover, a homogeneous morphology without cracking and fracture was obtained at the fiber/resin interface, as the appropriate porous structure and enough strength of the aerogel networks to decrease and withstand the capillary pressure at the liquid/gas interface during the drying at ambient pressure, prevent the aerogel networks from collapse. Due to the low bulk density (0.18g/cm(3)), high porosity (similar to 90%) and unique fiber geometry (a typical 2D planar random structure with the carbon fibres in the xy direction are distributed homogeneously in plane, while in the z direction over the height of the composite) of the CBCF fabric, the obtained composite possessed low bulk density (0.32- 0.45 g/cm(3)), high compressive strength (0.8-2.8 MPa for different directions) and low thermal conductivity (0.098-0.148 W/(mK)). More importantly, good thermal ablative and insulative properties in oxy-acetylene flame simulated high temperature environment (linear ablation rate as low as 0.085 mm/s, internal temperature peaks below 200 degrees C at 38 mm in-depth position as the surface temperature approximately 1800 degrees C). Therefore, the novel lightweight aerogels and composites are excellent heat-insulation and thermal-protection materials with applications in the fields of energy-saving and aerospace.

Enhanced Toughness and Sound Absorption Performance of Bio-Aerogel via Incorporation of Elastomer

Hydrophobic and thermal-insulating aerogels based on rigid cellulose nanocrystal and elastic rubber

Chitosan/clay aerogel: Microstructural evolution, flame resistance and sound absorption

Ultralight Biomass Aerogels with Multifunctionality and Superelasticity Under Extreme Conditions

Load‐Bearing Structure Inspired Cellulose‐Based Aerogel With High Resilience and Water Tolerance

Sound absorption, structure and mechanical behavior of konjac glucomannan-based aerogels with addition of gelatin and wheat straw

Microstructural evolution of bio-based chitosan aerogels for thermal insulator with superior moisture/fatigue resistance and anti-thermal-shock

Cellulose Nanofibrils/Xyloglucan Bio-Based Aerogels with Shape Recovery

Radially and Axially Oriented Ammonium Alginate Aerogels Modified with Clay/Tannic Acid and Crosslinked with Glutaraldehyde

Rigid and Fire-Resistant All-Biomass Aerogels

Robust Silica–Agarose Composite Aerogels with Interpenetrating Network Structure by in Situ Sol–Gel Process

Ultrahigh-strength silicone aerogels reinforced by an armor-like epoxy framework via a temperature-controlled sequential reaction strategy

Preparation, mechanical, acoustic and thermal properties of silica composite aerogel using wet-laid glass fiber felt as scaffold

Silica Aerogels with Self-Reinforced Microstructure for Bioinspired Hydrogels

Ultra-high strength, highly deformable and superhydrophobic polybenzoxazine@cellulose nanofiber composite aerogel for thermal insulation

Fabrication of Elastic Silica-Bacterial Cellulose Composite Aerogels with Nanoscale Interpenetrating Network by Ultrafast Evaporative Drying

Low-temperature superelastic, anisotropic, silane-crosslinked sodium alginate aerogel for thermal insulation

Characterization, Mechinical, Thermal And Ablative Properties Of Ceramic Modified Phenolic Resin Aerogels Synthsized By Ambient Pressure Drying

Zinc Borate Nanoparticle-Loaded Carboxymethyl Chitosan Aerogels for Flame Retardancy and Acoustic Absorption

Anisotropic cellulose nanofiber/chitosan aerogel with thermal management and oil absorption properties

Superior Stable, Hydrophobic and Multifunctional Nanocellulose Hybrid Aerogel Via Rapid UV Induced In-Situ Polymerization