Abstract:The unique characteristics of gas-solids two-phase flow and fluidization in terms of the flow structures and the apparent behavior of particles and fluid-particle interactions are closely linked to physical properties of the particles, operating conditions and bed configurations. Fluidized beds behave quite differently when solid properties, gas velocities or vessel geometries are varied. An understanding of hydrodynamic changes and how they, in turn, influence the transfer and reaction characteristics of chemical and thermal operations by variations in gas-solid contact, residence time, solid circulation and mixing and gas distribution is very important for the proper design and scale-up of fluidized bed reactors. In this paper, rather than attempting a comprehensive survey, we concentrate on examining some important positive and negative impacts of particle sizes, bubbles, clusters and column walls on the physical and chemical aspects of chemical reactor performance from the engineering application point of view with the aim of forming an adequate concept for guiding the design of multiphase fluidized bed chemical reactors. One unique phenomenon associated with particle size is that fluidized bed behavior does not always vary monotonically with changing the average particle size. Different behaviors of particles with difference sizes can be well understood by analyzing the relationship between particle size and various forces. For both fine and coarse particles, too narrow a distribution is generally not favorable for smooth fluidization. A too wide size distribution, on the other hand, may lead to particle segregation and high particle elutriation. Good fluidization performance can be established with a proper size distribution in which inter-particle cohesive forces are reduced by the lubricating effect of fine particles on coarse particles for Type A, B and D particles or by the spacing effect of coarse particles or aggregates for Type C powders. Much emphasis has been paid to the negative impacts of bubbles, such as gas bypassing through bubbles, poor bubble-to-dense phase heat & mass transfer, bubble-induced large pressure fluctuations, process instabilities, catalyst attrition and equipment erosion, and high entrainment of particles induced by erupting bubbles at the bed surface. However, it should be noted that bubble motion and gas circulation through bubbles, together with the motion of particles in bubble wakes and clouds, contribute to good gas and solids mixing. The formation of clusters can be attributed to the movement of trailing particles into the low-pressure wake region of leading particles or clusters. On one hand, the existence of down-flowing clusters induces strong solid back-mixing and non-uniform radial distributions of particle velocities and holdups, which is undesirable for chemical reactions. On the other hand, the formation of clusters creates high solids holdups in the riser by inducing internal solids circulations, which are usually beneficial for increasing concentrations of solid catalysts or solid reactants. Wall effects have widely been blamed for complicating the scale-up and design of fluidized-bed reactors. The decrease in wall friction with increasing the column diameter can significantly change the flow patterns and other important characteristics even under identical operating conditions with the same gas and particles. However, internals, which can be considered as a special wall, have been used to improve the fluidized bed reactor performance. Generally, desirable and undesirable dual characteristics of interaction between particles and fluid are one of the important natures of multiphase flow. It is shown that there exists a critical balance between those positive and negative impacts. Good fluidization quality can always be achieved with a proper choice of right combinations of particle size and size distribution, bubble size and wall design to alleviate the negative impacts.

CFD Simulation of the Hydrodynamics in Three Phase Fluidized Bed Reactor: Effect of Particle Properties

CFD Simulation of an Agitated Gas-Fluidized Bed: Effects of Particle–particle Restitution Coefficient on the Hydrodynamics

Experimental and numerical investigation of solid behavior in a gas–solid turbulent fluidized bed

CFD Simulation and Experiments of Dynamic Parameters in Gas–solid Fluidized Bed

Multi-scale Characteristics and Gas-Solid Interaction among Multiple Beds in a Dual Circulating Fluidized Bed Reactor System

Numerical Simulations of Flow Structure and Heat Transfer in a Central Jet Bubbling Fluidized Bed

Effect of Bed Thickness on a Pseudo 2D Gas-Solid Fluidized Bed Turbulent Flow Structures and Dynamics

Particle-scale Simulation of Fluidized Bed with Immersed Tubes

Multi-scale simulation of particle density effects on hydrodynamics in dense gas-solid fluidized beds

Experimental Research on the Gas-Solid Flow Characteristics in Large-Scale Dual Fluidized Bed Reactor

Numerical Simulation Study on the Gas–Solid Flow Characteristics of a Large-Scale Dual Fluidized Bed Reactor: Verification and Extension

Large eddy simulation of particle hydrodynamic characteristics in a dense gas-particle bubbling fluidized bed

Study on a Semi-Resolved CFD-DEM Method for Rod-Like Particles in a Gas-Solid Fluidized Bed

Modelling of Dense Gas-Particle Flow in a Circulating Fluidized Bed by Distinct Cluster Method (DCM)

The effect of collision parameters on the 3D Eulerian simulation of a thin rectangular bubbling fluidized bed

CFD Investigation of Particle Fluctuation Characteristics of Bidisperse Mixture in a Gas–solid Fluidized Bed

CFD-DEM study of impacts of the porous distributor medium on fluidization characteristics of a 2D-fluidized bed

A Euler-Euler Hydrodynamic Modelling and Simulation of Dense Particle Flow in a Small-Scale Fluidized Bed

Dual Characters of Interaction Between Particles and Fluid

CFD Modeling of Three-phase Bubble Column: 2. Effect of Design Parameters

CFD Modeling of Flow Pattern and Phase Holdup of Three Phase Fluidized Bed Contactor