Abstract:Multi-material fused deposition 3D printing has the unique ability to maintain complex shapes and add special properties. However, the narrow selection of consumable materials, low printing efficiency, and poor performance of the finished products limit the application scope of this technology. In this paper, we propose a twin-screw extrusion 3D printing system that can print a variety of powdered or granular materials, including environmentally friendly biomass particles, metal particles, and thermoplastics, and that enables the mixing of heterogeneous materials. Then we investigate the heat transfer and rheological properties of the system’s material extrusion process. Through the coupled thermal-fluid-solid multi-physical field simulation of the nozzle system, we qualitatively and quantitatively study the transport law and thermal flow field distribution characteristics of the material within the extrusion system, analyze the transport and melting mechanism of the hot melt in the runner during the extrusion process, and obtain the mechanism of the influence of the structural design parameters and the 3D printing process parameters on the transient flow field characteristics and mixing performance. When the screw’s outer diameter is 20 mm and the speed range is 5–25 r/min, the nozzle extrusion flow rate is 2.45–20.15 mm3/s, and the printing efficiency is 3–4 times that of traditional wire printing. The flow field characteristic parameters are optimal when the screw lead is 24–36 mm, and the material extrusion effect is best when the rotational speed is 8–15 r/min. The heat flow field distribution in the extrusion system is stable, the speed distribution is reasonable, and the temperature field distribution is uniform. There is no solution reflux or overflow at the nozzle, the nozzle is not blocked, and the material can be extruded at constant temperature and pressure. The strength of the twin-screw is within the allowable range, the mixing performance is good, and the material can be transported forward with positive displacement. The maximum thermal deformation of the nozzle is 0.09861 mm, which is much smaller than the maximum deformation precision of 0.2 mm, indicating that the screw and nozzle are reasonably designed. The simulation proves the reasonableness of the calculation results.

Boundary-Conforming Finite Element Methods for Twin-Screw Extruders using Spline-Based Parameterization Techniques

Boundary-Conforming Finite Element Methods for Twin-Screw Extruders: Unsteady - Temperature-Dependent - Non-Newtonian Simulations

Three-dimensional Numerical Study of the Mixing Behaviour of Twin-screw Elements

Numerical design of distributive mixing elements

Combining Boundary-Conforming Finite Element Meshes on Moving Domains Using a Sliding Mesh Approach

Study of Dynamic Flow and Mixing Performances of Tri-Screw Extruders with Finite Element Method

Spline-Based Space-Time Finite Element Approach for Fluid-Structure Interaction Problems With a Focus on Fully Enclosed Domains

Coupled thermal-force finite element analysis for a twin-screw extruder barrel with two heating pipelines in the axial direction

Simulation of Free Surface Flow with A Revolving Moving Boundary for Screw Extrusion Using Smoothed Particle Hydrodynamics

Generalized predictions of the pumping characteristics and viscous dissipation of single‐screw extruders including three‐dimensional curvature effects

A generalized method aiming at predicting the polymer melt flow field in the metering zone of large-scale single-screw extruders

Predicting the Non-Linear Conveying Behavior in Single-Screw Extrusion: A Comparison of Various Data-Based Modeling Approaches used with CFD Simulations

Numerical study of mixing dynamics inside the novel elements of a corotating nontwin screw extruder

Analysis of the Dispersive and Distributive Mixing Effect of Screw Elements on the Co-Rotating Twin-Screw Extruder with Particle Tracking

An embedded boundary approach for efficient simulations of viscoplastic fluids in three dimensions

The momentum-consistent smoothed particle Galerkin (MC-SPG) method for simulating the extreme thread forming in the flow drill screw-driving process

A Dual Domain Method for 3-D Flow Simulation

Cartesian grid method with a consistent direct discretization approach for numerical simulation of non-Newtonian fluid flow

A nodal-integration-based finite element method for solving steady-state nonlinear problems in the loading's comoving frame

Structural design and heat transfer analysis of twin-screw extrusion 3D printer

Improvement in an Analytical Approach for Modeling the Melting Process in Single-Screw Extruders