Abstract:3D printing of continuous carbon fiber reinforced thermoplastic (CFRTP) composites is increasingly under development owing to its unparalleled flexibility of manufacturing 3D structures over traditional manufacturing processes. However, key issues, such as weak interlayer bonding, voids between beads and layers, and low volume ratio of carbon fiber, in the mainstream fuse deposition modeling (FDM) and extrusion suppress the applications of these techniques in mission‐critical applications, such as aerospace and defense. This communication reports a novel approach, inspired by laminated object manufacturing (LOM), for 3D printing of continuous CFRTPs using prepreg composite sheets. The prepreg sheets are successively cut based on the sliced CAD geometry, and then bonded layer upon layer using a CO2 laser beam and a consolidation roller system. The void content is low by computed tomography scans and interlaminar bonding strength is as high as conventional autoclave method by lap shear strength tests. The excellent interfacial bonding strength and high volume ratio of continuous carbon fiber contribute to the highest reported tensile strength (668.3 MPa) and flexural strength (591.16 MPa) to date, for all 3D printed CFRTPs. Moreover, the proposed technique also enables controlling the alignment of carbon fiber in printed layers. CFRTPs with unidirectional [0°]s, cross‐ply [0/90°]s, and [0/‐45/0/45°]s fiber reinforcement are produced and evaluated for mechanical properties. The proposed 3D printing method is broadly beneficial for industries requiring high performance and lightweight structural materials with complex geometries. A mechanism to 3D print ultrahigh strength carbon fiber reinforced polymer (CFRP) composites capable of achieving aligned continuous carbon fiber reinforcement is presented. The mechanical properties are superior to the existing 3D printed CFRP materials due to an excellent interfacial bonding and minimal void content. During this laser assisted 3D printing technique, temperature at the material interface reaches well above the matrix melting point.

A novel overflow extrusion‐annealing process for preparing high performance recycled carbon fiber reinforced Nylon 6 composites

A Novel Approach on Recycling Short-Chopped Carbon Fibers by Electric Field Induced Manipulation

3D printing for continuous fiber reinforced thermoplastic composites: mechanism and performance

Designing Prepregnation and Fused Filament Fabrication Parameters for Recycled PP- and PA-Based Continuous Carbon Fiber Composites

Fused-Deposition Modeling 3D Printing of Short-Cut Carbon-Fiber-Reinforced PA6 Composites for Strengthening, Toughening, and Light Weighting

3D Printing of Ultrahigh Strength Continuous Carbon Fiber Composites

Carbon-Fiber-Recycling Strategies: A Secondary Waste Stream Used for PA6,6 Thermoplastic Composite Applications

Facile preparation, closed-loop recycling of multifunctional carbon fiber reinforced polymer composites

Optimal short carbon fiber‐reinforced polyamide 6 composites with lifted high strength and toughness for fused filament fabrication

3D Printing Technology for Short-continuous Carbon Fiber Synchronous Reinforced Thermoplastic Composites: A Comparison between Towpreg Extrusion and In Situ Impregnation Processes

Preparation of short CF/GF reinforced PEEK composite filaments and their comprehensive properties evaluation for FDM-3D printing

A Novel Route to Fabricate High-Performance 3D Printed Continuous Fiber-Reinforced Thermosetting Polymer Composites

Reinforcing Efficiency of Recycled Carbon Fiber PLA Filament Suitable for Additive Manufacturing

Additive manufacturing of high‐strength polyamide 6 composites reinforced with continuous carbon fiber prepreg

Study on recycled carbon fiber obtained by thermal activated oxide semiconductor and mechanical properties of its reinforced polymer composites

Process optimization of continuous flax fiber/polylactic acid prepreg filaments toward high performance 3D‐printed composites

An investigation of preparation of continuous carbon fiber reinforced PLA prepreg filament

Recent progress of 3D printed continuous fiber reinforced polymer composites based on fused deposition modeling: a review

Development of high performance recycled carbon fibre composites with an advanced hydrodynamic fibre alignment process

Design and Extrusion-Based 3D Printing of Continuous Fiber Composites: Status, Challenges, and Opportunities

Effect of process parameters on properties of 3D printed continuous fiber reinforced thermoplastic composites