Abstract:This study prepares composite panels with three Polylactic acid (PLA)-based materials via the multi-material fused filament fabrication method. The influences of four processing parameters on the mechanical properties of 3D-printed samples are investigated employing the Taguchi method. These parameters include the relative volume ratio, material printing order, filling pattern, and filling density. A "larger is better" signal-to-noise analysis is performed to identify the optimal combination of printing parameters that yield maximum bending strength and bending modulus of elasticity. The results reveal that the optimal combination of printing parameters that maximizes the bending strength involves a volume ratio of 1:1:2, a material sequence of PLA/foam-agent-modified eco-friendly PLA (ePLA-LW)/glass fiber-reinforced eco-friendly PLA (ePLA-GF), a Gyroid filling pattern, and a filling density of 80%, and the optimal combination of printing parameters for maximum bending modulus involves a volume ratio of 1:2:1 with a material sequence of PLA/ePLA-LW/ePLA-GF, a Grid filling pattern, and 80% filling density. The Taguchi prediction method is utilized to determine an optimal combination of processing parameters for achieving optimal flexural performances, and predicted outcomes are validated through related experiments. The experimental values of strength and modulus are 43.91 MPa and 1.23 GPa, respectively, both very close to the predicted values of 46.87 MPa and 1.2 GPa for strength and modulus. The Taguchi experiments indicate that the material sequence is the most crucial factor influencing the flexural strength of the composite panels. The experiment result demonstrates that the flexural strength and modulus of the first material sequence are 67.72 MPa and 1.53 GPa, while the flexural strength and modulus of the third material sequence are reduced to 27.09 MPa and 0.72 GPa, respectively, only 42% and 47% of the first material sequence. The above findings provide an important reference for improving the performance of multi-material 3D-printed products.

Experimental Investigation on the Static and Dynamic Behavior of Passive Controlled Bio Composite Manufactured Via 3D Printing Technique

Experimental and Theoretical Studies on 3D Printed Short and Continuous Carbon Fiber Hybrid Reinforced Composites

Investigating mechanical properties of 3D printed polylactic acid / poly-3-hydroxybutyrate composites. Compressive and fatigue performance

PLA-Based Composite Panels Prepared via Multi-Material Fused Filament Fabrication and Associated Investigation of Process Parameters on Flexural Properties of the Fabricated Composite

Investigation on the mechanical properties of 3D printed hybrid continuous fiber-filled composite considering influence of interfaces

Mechanical and Energy Absorption Behaviors of 3D Printed Continuous Carbon/kevlar Hybrid Thread Reinforced PLA Composites

Flexure Behaviors of ABS-based Composites Containing Carbon and Kevlar Fibers by Material Extrusion 3D Printing

Mechanical performances of printed carbon fiber-reinforced PLA and PETG composites

Preparation and Evaluation of the Tensile Characteristics of Carbon Fiber Rod Reinforced 3D Printed Thermoplastic Composites

Additive manufacturing of mechanical testing samples based on virgin poly (lactic acid) (PLA) and PLA/wood fibre composites

Influence of the Manufacturing Method (3D Printing and Injection Molding) on Water Absorption and Mechanical and Thermal Properties of Polymer Composites Based on Poly(lactic acid)

Investigation of Fused Deposition Modelling Process Parameters in 3D Printing for Composite Material (Poly Lactic Acid and Banana Fibre)

Mechanical, microstructural and numerical investigations of 3D printed carbon fiber reinforced PEEK

Evaluation of stress-controlled high-cycle fatigue characteristics in PLA-wood fused deposition modeling 3D-printed parts under bending loads

Experimental analysis and optimization of mechanical properties of FDM-processed polylactic acid using Taguchi design of experiment

Study on performance characteristics of fused deposition modeling 3D ‐printed composites by blending and lamination

Evaluation of fatigue characteristics of 3D printed/composites reinforced with carbon fiber using design of experiments

Fabrication, mechanical, finite element and In vitro evaluation of 3D printed polylactide/biphasic calcium phosphate composite blends

Fundamental study and modification of Kenaf fiber reinforced polylactic acid bio-composite for 3D printing filaments

Determination of shear strength of additively manufactured poly lactic acid/flax fibre bio-composite via the iosipescu test

Optimization of Fused Deposition Modeling Process Parameters and Dynamic Mechanical Analysis of 3D Printed Polycarbonate/Acrylonitrile-Butadiene-Styrene Composite Loaded with Tetrabromobiphenol-A and Microcrystalline Cellulose