Impact of breech geometry and propellant flow on the release of large pellets for the ITER disruption mitigation system

Trey E Gebhart,Larry R Baylor,Mathias Dibon,M Nance Ericson,Eliot James Felske,Shane Frank,Walter Gardner,Adriana Gabrielle Ghiozzi,Stefan Jachmich,Uron Kruezi,Michael Lehnen,Danah Velez

DOI: https://doi.org/10.1088/1741-4326/ad2424

IF: 3.3

2024-01-31

Nuclear Fusion

Abstract:Studies have been performed on the release mechanism for large pellets using high pressure gas in a shattered pellet injector. Typically, pellets are dislodged from the cryogenic surface and accelerated down a barrel using high pressure gas delivered by a fast-acting propellant valve. The pellets impact an angled surface which shatters the pellet into many small fragments before entering the plasma. This technique was initially demonstrated on DIII-D and is now deployed on JET, KSTAR, ASDEX-Upgrade, and other tokamaks around the world in support of ITER's disruption mitigation system design and physics basis. The large hydrogen, 28.5 mm diameter, 2 length-to-diameter ratio, pellets foreseen for ITER SPI operation have low material strength and low heat of sublimation, which cause the pellets to be fragile and highly reactive to the impact of warm propellant gas. Due to the size of the pellets, significantly more propellant gas is required to dislodge and accelerate them. This creates a potentially significant propellant gas removal issue as 2 to 6 bar-L of gas is expected to be required for release and speed control. The research presented in this paper is an in-depth exploration of the parameters that are keys to reliable pellet release and speed control. Computational fluid dynamics (CFD) modeling of propellant flows through various breech designs was conducted to determine the force generated on the back surface of a pellet. These simulations assumed the use of the ORNL designed flyer plate valve. CFD modeling combined with experimental measurements provide adequate insight to determine a path to an optimal valve and breech design for ITER SPI pellet release and speed control while minimizing propellant gas usage.

physics, fluids & plasmas

What problem does this paper attempt to address?

The problem that this paper attempts to solve is how to reliably release and control the velocity of large hydrogen pellets (with a diameter of 28.5 mm and a length - to - diameter ratio of 2) during Shattered Pellet Injection (SPI) in the International Thermonuclear Experimental Reactor (ITER). Due to the characteristics of low material strength and low sublimation heat of these large hydrogen pellets, they are very fragile and reactive when impacted by warm propellant gases. In addition, in order to loosen and accelerate these pellets from the cryogenic surface, significantly more propellant gas is required, which may lead to propellant gas removal problems, as 2 to 6 bar - liters of gas are expected to be used for release and velocity control.

Specifically, the research focuses on the following aspects:
1. **Influence of propellant gas flow rate**: Through Computational Fluid Dynamics (CFD) modeling, study the influence of different propellant valve designs on the forces generated on the rear surface of the pellet.
2. **Optimization of chamber geometry**: Explore different chamber geometries (such as conical chamber volume reducers and nozzle - shaped chamber volume reducers) to optimize the pellet release process, reduce the amount of propellant gas used, and improve the integrity of the pellets.
3. **New valve design**: Design a new small Flapper Plate Valve (FPV) with an outlet diameter of 8 mm and a volume of 0.25 liters to reduce the amount of propellant gas used and improve the reliability of the system.
4. **Chamber optimization and pellet force analysis**: Use Python code to simulate the process of pressure rise in the chamber, pellet detachment, and subsequent acceleration along the barrel to determine the optimal chamber volume and propellant gas flow rate.

Through these studies, the authors aim to provide a reliable pellet release and velocity control scheme for the SPI system in ITER while minimizing the amount of propellant gas used.