Abstract:Portable electronics and their commercial use are strongly dependent on the prize, performance and life cycle of the rechargeable batteries. This is even truer for the use in electric vehicles. Currently used Li+-ion batteries represent the state of art technology but there still is a strong demand for further improvement [1,2]. Low abundance and thus high costs for lithium have initiated intensive research for the possible replacement of lithium by other more abundant metals such as magnesium and sodium [3]. Ionic, electronic and chemical characteristics of Li+-, Na+- and Mg2+-ions are different and therefore host materials appropriate for Li+-ions intercalation are not necessarily suitable for Mg2+ and Na+ ions – as well known for the case of graphite anodes. The cathode material V2O5 is one candidate which already showed good performance not just for Li+ but also for Mg2+ and Na+ions [4,5]. Since the morphology and structure of the host materials strongly influence the intercalation process, in this study efforts have been done to synthesize V2O5 with different morphology by applying different synthetic routes and choosing the best material for the metal ion intercalation. V2O5 was prepared by means of sonochemical modification of commercial V2O5 powder, anodization of V metal, electrochemical deposition and hydrothermal synthesis. The obtained materials were characterized by means of scanning electron microscopy, X-ray diffraction and X-ray photoelectron spectroscopy. The sonochemical treatment and electrochemical deposition yielded V2O5-nanofibers, the anodization method V2O5-nanotubes and the hydrothermal synthesis hollow nanospheres of V2O5. The performance of the obtained materials was tested by several electrochemical techniques such are cyclic voltammetry, potentiostatic intermittent titration technique (PITT) and galvanostatic charge/discharge cycles. Li, Na and Mg intercalation were studied. For Li, the rate capability of the sonochemically prepared material was clearly improved compared to commercial, microcrystalline V2O5, but the available voltage at a given discharge capacity was less. The electrodeposited material showed a rather poor performance, while the hollow nanospheres behaved very promising. Also for Na intercalation the latter material showed reasonable performance. First measurements for Mg insertion are shown as well. [1] Dunn B. et al., Electrical Energy Storage for the Grid: A Battery of Choices, Science 334 (2011) 928 [2] Gachot G. et al., Deciphering the multi-step degradation mechanisms of carbonate-based electrolyte in Li batteries, Journal of Power Sources 178 (2008) 409 [3] Besenhard J. et al., Advances in battery technology: rechargeable magnesium batteries and novel negative-electrode materials for lithium ion batteries, ChemPhysChem 3 (2002) 155 [4] Gershinsky G. et al., Electrochemical and Spectroscopic Analysis of Mg2+ Intercalation into Thin Films Electrodes of Layered Oxides: V2O5 and MoO3, Langmuir 29 (2013) 10964 [5] Su D. W. et al., Hierarchical orthorhombic V2O5hollow nanospheres as high performance cathode materials for sodium-ion batteries, J. Mater. Chem. 2 (2014) 11185

Ab initio study of Li, Mg and Al insertion into rutile VO2: Fast diffusion and enhanced voltages

In-situ TEM Experiments and First-Principles Studies on the Electrochemical and Mechanical Behaviors of Α-Moo3 in Li-ion Batteries

Lithiation and Magnesiation Mechanism of VOCl: First-Principles Moleculardynamics Simulation

First principles study on the li storage performance of MoO2

First-Principles Analysis of Li Intercalation in VO2(B)

Phase Transformation and Diffusion Kinetics of V2O5 Electrode in Rechargeable Li and Mg Batteries: A First-Principle Study

Non-destructive Chemical Prelithiation of VO2(B) Anodes Constructing a Multifunctional Interphase Layer for Advanced Li-Ion Batteries

Artificial Cathode-Electrolyte Interphase towards High-Performance Lithium-Ion Batteries: A Case Study of β-AgVO3

Single-layered V2O5 a promising cathode material for rechargeable Li and Mg ion batteries: an ab initio study.

Ultrafast Knock-Off Li+ Diffusion and Subtle Structural Evolution of Li5V3O8 Anode in Lithium-Ion Batteries

Development of V2O3 Nanostructures for Alkali Metal Ion Batteries: A Novel Approach through Mild Metal Vapor Reduction and Interface Engineering

V2O5 As the Cathode for Mg2+-Ion Batteries, Preparation and Characterization

Progress on Li3VO4 as a Promising Anode Material for Li-ion Batteries: Li3VO4 As Anode Material

Progress on Li3VO4 as a Promising Anode Material for Li‐ion Batteries

Cation reordering instead of phase transitions: Origins and implications of contrasting lithiation mechanisms in 1D ζ- and 2D α-V2O5

Insights into stability, electronic properties, defect properties and Li ions migration of Na, Mg and Al-doped LiVPO4F for cathode materials of lithium ion batteries: A first-principles investigation

Electrochemical Characteristics of Lithium Vanadate, Li3VO4 As a New Sort of Anode Material for Li-ion Batteries

Synthesis, Tailoring and Characterization of V2O5-Cathodes for High Performance Li+-, Na+- and Mg2+-Ion Batteries

Open-tunneled oxides as intercalation host for multivalent ion (Ca and Al) batteries: A DFT study

First-principles Investigation of Aluminum Intercalation and Diffusion in TiO2 Materials: Anatase Versus Rutile

Rich Alkali Ions Preintercalated Vanadium Oxides for Durable and Fast Zinc-Ion Storage