Abstract:Carbon nanotube(CNT)/polymer composite materials have been widely studied for two decades.However,there remains a common and critical challenge,i.e.,random dispersion of CNTs in polymer matrices,which has largely lowered their properties and limited their applications.Herein,we have developed a general method to prepare highly aligned CNT/polymer composite materials in formats of array,film,and fiber.The key procedure is to synthesize spinnable CNT arrays with high quality by a chemical vapor deposition process.Fe/Al2O3 was used as catalyst,ethylene was used as carbon source,a mixture gas of argon and hydrogen was used as carrying gas.The optimal growth conditions were summarized as below: thickness of 1.2 nm for Fe,thickness of 3 nm for Al2O3,flow rate of 400 standard cm3/min for argon,flow rate of 90 standard cm3/min for ethylene,flow rate of 30 standard cm3/min for hydrogen,growth temperature of 740 ℃,and growth time of 10 min.Here the catalyst system was coated on silicon substrate by electron beam evaporation with rates of 0.5 and 2 /s for Fe and Al2O3,respectively.To prepare CNT sheets or fibers,the spinnable array was first stabilized in a stage.A blade was then used to draw a ribbon out of the array.A CNT sheet would be obtained if the ribbon was directly pulled out without rotation,while a fiber should be produced if a rotary spinning was used.The spinning speed was about 15 cm/min.Monomer/polymer solutions or melts were directly coated onto the aligned CNT sheet or fiber to produce the aligned CNT/polymer film or fiber.Due to the high alignment of CNTs in polymer matrices,the resulting composite materials exhibited remarkable physical properties,e.g.,the mechanical strength and electrical conductivity can be improved for one and three orders compared with the conventional solution blending method,respectively.These novel composite materials are promising for a wide variety of applications.The use of them as novel counter electrodes to fabricate dye-sensitized solar cells has been investigated as a demonstration.In a typical fabrication,an aligned CNT/polymer film(typical thickness of 5 μm) was first transferred onto fluorine doped tin oxide as counter electrode.A layer of TiO2 was coated onto fluorine doped tin oxide as working electrode,followed by immersion into 0.5 mmol/L cis-diisothiocyanato-bis(2,2'-bipyridyl-4,4'-dicarboxylato) ruthenium(II) bis(tetrabutylammonium)(also called N719) solution in a mixture solvent of acetonitrile/tert-butanol(volume ratio of 1/1) for 16 h.After being further rinsed with acetonitrile and dried,the N719-incorporated TiO2 electrode was assembled with the counter electrode.An electrolyte which consisted of LiI,I2,2-2-3-with propyl methyl 5-membered imidazole iodine,GuSCN,and tri-butyl-phosphate in dehydrated acetonitrile was injected into the cell through a hole on the counter electrode.The hole was finally sealed with surlyn and a piece of glass.

Removing Conjugated Polymers from Aligned Carbon Nanotube Arrays.

Removal of Conjugated Polymer on Carbon Nanotube Array by Dry Process

Improving the Performance of Aligned Carbon Nanotube-Based Transistors by Refreshing the Substrate Surface.

Achieving High-Performance Polymer-Wrapper-Free Aligned Carbon Nanotube Field-Effect Transistors Through Degradable Polymer Wrapping and Efficient Removal Techniques

Polymer Coating Enabled Carrier Modulation for Single-Walled Carbon Nanotube Network Inverters and Antiambipolar Transistors

Transferable thin films of pristine carbon nanotubes.

Monolithic Three‐dimensional Integration of Aligned Carbon Nanotube Transistors for High‐performance Integrated Circuits

Aligning Solution-Derived Carbon Nanotube Film with Full Surface Coverage for High-Performance Electronics Applications.

Structurally Analogous Degradable Version of Fluorene-Bipyridine Copolymer with Exceptional Selectivity for Large-Diameter Semiconducting Carbon Nanotubes

Scalable Preparation of High-Density Semiconducting Carbon Nanotube Arrays for High-Performance Field-Effect Transistors.

Aligned, high-density semiconducting carbon nanotube arrays for high-performance electronics

Controlled Removal of Individual Carbon Nanotubes from Vertically Aligned Arrays for Advanced Nanoelectrodes

Selective Chemistry-Based Separation of Semiconducting Single-Walled Carbon Nanotubes and Alignment of the Nanotube Array Network under Electric Field for Field-Effect Transistor Applications

Realizing Controllable Carbon Nanotube Arrays for Soft Devices by Asymmetric Langmuir–Blodgett and Hydrophilization Process

Wet Purification of Aligned Carbon Nanotube Arrays and Its Impact on the Morphology of the Carbon Nanotube Arrays

Using Nanoscale Thermocapillary Flows to Create Arrays of Purely Semiconducting Single-Walled Carbon Nanotubes

Preparation and Application of Aligned Carbon Nanotube/Polymer Composite Material

A Facile Method to Align Carbon Nanotubes on Polymeric Membrane Substrate.

Degradable Fluorene- and Carbazole-Based Copolymers for Selective Extraction of Semiconducting Single-Walled Carbon Nanotubes

Removable and Recyclable Conjugated Polymers for Highly Selective and High-Yield Dispersion and Release of Low-Cost Carbon Nanotubes

Length-dependent Alignment of Large-Area Semiconducting Carbon Nanotubes Self-Assembly on a Liquid-Liquid Interface