Abstract:The objective of this study was to investigate the properties of enteric matrix pellets that were prepared by hot-melt extrusion in a one-step, continuous process. Five polymers (Eudragit) L100-55, L100 and S100, Aqoat grades LF and HF) were investigated as possible matrix formers, and pellets prepared with Eudragit S100 demonstrated superior gastric protection and acceptable processibility. Extruded pellets containing Eudragit S100 and up to 40% theophylline released less than 10% drug over 2h in acid, however, the processibility and yields were compromised by the high amounts of the non-melting drug material in the formulation. Efficient plasticization of Eudragit S100 was necessary to reduce the polymer's glass transition temperature and melt viscosity. Five compounds including triethyl citrate, methylparaben, polyethylene glycol 8000, citric acid monohydrate and acetyltributyl citrate were investigated in terms of plasticization efficiency and preservation of the delayed drug release properties. The aqueous solubility of the plasticizer and its plasticization efficiency impacted the drug release rate from the matrix pellets. The use of water-soluble plasticizers resulted in a loss of gastric protection, whereas low drug release rates in acid were found for pellets containing insoluble plasticizers or no plasticizer, independent of the extent of Eudragit S100 plasticization. The release rate of theophylline in buffer pH 7.4 was faster for pellets that were prepared with efficient plasticizers. The microstructure and solid-state properties of plasticized pellets were further investigated by scanning electron microscopy and powder X-ray diffraction. Pellets prepared with efficient plasticizers (TEC, methylparaben, PEG 8000) exhibited matrices of low porosity, and the drug was homogeneously dispersed in its original polymorphic form. Pellets containing ATBC or citric acid monohydrate had to be extruded at elevated temperature and showed physical instabilities in the form of recrystallization at room temperature. Enteric matrix pellets with a diameter below 1mm and containing 30% theophylline could be successfully prepared by hot-melt extrusion when Eudragit S100 plasticized with either TEC or methylparaben was employed as the matrix material.

Floating hot-melt extruded tablets for gastroretentive controlled drug release system

Novel Hot Melt Extruded Matrices of Hydroxypropyl Cellulose and Amorphous Felodipine–Plasticized Hydroxypropyl Methylcellulose As Controlled Release Systems

Delayed Sustained Drug Release from Electrostatic Powder Coated Tablets with Ultrafine Polymer Blends

Physicochemical properties and mechanisms of drug release from melt-extruded granules consisting of chlorpheniramine maleate and Eudragit FS

Melt-Extruded Eudragit® FS-Based Granules for Colonic Drug Delivery

Evaluation of water uptake and mechanical properties of blended polymer films for preparing gas-generated multiple-unit floating drug delivery systems

Hot-Melt extrusion coupled with pressurized carbon dioxide for enhanced processability of pharmaceutical polymers and drug delivery applications - An integrated review

Properties of melt extruded enteric matrix pellets

Development of 3D-printed dual-release fixed-dose combination through double-melt extrusion

Formulation and Evaluation of Extended Release Floating Matrix Tablet of Eperisone Hydrochloride by Direct Compression Method

Improved drug delivery to the lower intestinal tract with tablets compression-coated with enteric/nonenteric polymer powder blends

Modulating Drug Release from Short Poly(ethylene Glycol) Block Initiated Poly(L-lactide) Di-block Copolymers

Development of a HPMC-based controlled release formulation with hot melt extrusion (HME)

Impact of Hot-Melt Extrusion on Glibenclamide's Physical and Chemical States and Dissolution Behavior: Case Studies with Three Polymer Blend Matrices

Development and Characterization of Sustained-Released Donepezil Hydrochloride Solid Dispersions Using Hot Melt Extrusion Technology

Controlled Release of Highly Hydrophilic Drugs from Novel Poly(Magnesium Acrylate) Matrix Tablets

Design and Evaluation of New Gel-Based Floating Matrix Tablets Utilizing the Sublimation Technique for Gastroretentive Drug Delivery

Cellulose Acetate Butyrate: Ammonio Methacrylate Copolymer Blends as a Novel Coating in Osmotic Tablets

Blends of enteric and GIT-insoluble polymers used for film coating: physicochemical characterization and drug release patterns

Preparation of Ethyl Cellulose Microspheres for Sustained Release of Sodium Bicarbonate.

Development of multiple structured extended release tablets via hot melt extrusion and dual-nozzle fused deposition modeling 3D printing