Abstract:In some circumstances, hybrid polymer microfluidic chips composed of both elastic, gas-permeable polydimethylsiloxane (PDMS) and rigid plastics are needed. However, it is quite difficult to bond PDMS irreversibly to plastics such as polystyrene (PS). In this article, a facile method for irreversible bonding of PDMS to PS was proposed based on UV/O-3-assisted surface modification in combination of surface silanization. Firstly, a PS sheet was exposed to UV/O-3 to produce oxygen-containing polar moieties, such as hydroxyl and carboxylic acid, on its surface. Secondly, the UV/O-3 treated PS sheet was silanized with (3-aminopropyl)triethoxysilane (APTES) via the reaction between the oxygen-containing polar moieties on the PS surface and the molecules of APTES. Thirdly, the silanized-PS sheet and the PDMS substrate with micro channel network were treated with UV/O-3 again to generate silanol moieties on both surfaces. Finally, the UV/O-3 treated PDMS was immediately brought intimate contact with the UV/O-3 treated silanized-PS, and irreversible bonding of PDMS with PS occurred after putting the PDMS-PS complex at room temperature for 1 h through the condensation reaction between silanol moieties. Contact angle measurement, X-ray photoelectron spectroscopy, total reflection Fourier transformation infrared spectrometer were applied to characterize the surface chemistry of the PS during the UV/O-3 treatment and silanization. The hybrid PDMS-PS microfludic chips prepared with the established method can bear a gas pressure higher than 0.5 MPa and a water stream at a flow rate higher than 170 mu L/min (the test channels were 2.5 cm in the length, 50 mu m in the width, 200 mu m in the depth). A hybrid PDMS-PS microfluidic chip composed of gas-permeable PDMS substrate with channel network and excellently biocompatible PS cover sheet was fabricated for cell culture. The experimental results showed that HeLa cells cultured in the hybrid PDMS-PS microchip grew much better than those cultured in the full PS microchip, and slightly better than those in the full PDMS microchip.

Grafting epoxy-modified hydrophilic polymers onto poly(dimethylsiloxane) microfluidic chip to resist nonspecific protein adsorption

Surface immobilization of polymer brushes onto porous poly(vinylidene fluoride) membrane by electron beam to improve the hydrophilicity and fouling resistance

Hydrophilic Biopolymer Grafted on Poly(dimethylsiloxane) Surface for Microchip Electrophoresis.

The Fabrication of Superlow Protein Absorption Zwitterionic Coating by Electrochemically Mediated Atom Transfer Radical Polymerization and Its Application

Controlled Grafting of Well-Defined Epoxide Polymers on Hydrogen-Terminated Silicon Substrates by Surface-Initiated Atrp at Ambient Temperature

In-Situ Grafting Hydrophilic Polymer on Chitosan Modified Poly (dimethylsiloxane) Microchip for Separation of Biomolecules

An Approach for Irreversible Bonding of PDMS-PS Hybrid Microfluidic Chips at Room Temperature

Surface-hydrophilic and protein-resistant silicone elastomers prepared by hydrosilylation of vinyl poly(ethylene glycol) on hydrosilanes-poly(dimethylsiloxane) surfaces

Synthesis of an Amphiphilic Glucose‐carrying Graft Copolymer and Its Use for Membrane Surface Modification

Deposition of PEG onto PMMA microchannel surface to minimize nonspecific adsorption.

Solution-phase Surface Modification in Intact Poly(dimethylsiloxane) Microfluidic Channels.

Covalent modified hydrophilic polymer brushes onto poly(dimethylsiloxane) microchannel surface for electrophoresis separation of amino acids

Covalently Attached Slippery Surface Coatings to Reduce Protein Adsorptions on Poly(dimethylsiloxane) Planar Surfaces and 3D Microfluidic Channels

Restraining non-specific adsorption of protein using Parylene C-caulked polydimethylsiloxane.

Methacrylate polymer layers bearing poly(ethylene oxide) and phosphorylcholine side chains as non-fouling surfaces: in vitro interactions with plasma proteins and platelets.

Proteins Modification of Poly(dimethylsiloxane) Microfluidic Channels for the Enhanced Microchip Electrophoresis.

Separation of Proteins on Surface‐modified Poly(dimethylsiloxane) Microfluidic Devices

Inhibition of non-specific protein adsorption on PMMA surface: The role of surface modification

Modification of Poly(dimethylsiloxane) Microfluidic Channels with Silica Nanoparticles Based on Layer-by-layer Assembly Technique

Surface Functionalization of Poly(N-Vinylpyrrolidone) onto Poly(Dimethylsiloxane) for Anti-Biofilm Application

Polymeric Microfluidic Devices Fabricated Using Epoxy Resin for Chemically Demanding and Day-Long Experiments