Abstract:Abstract Precise tooling is vital for defect-free production of micro injection moulded (μ-IM) or hot-embossed products. The demoulding stage of such moulding and forming processes poses a serious challenge to the integrity of thin miniature features because of friction, adhesion, and thermal stresses. Typically, micro moulds involve geometrically textured patterns or features such as linear ridges, pillars, channels, and holes, the characteristic dimensions of which range from 10 to 300 μm. Realistically complex mould designs, containing precision micro features (enhanced fillet radius and positive draft angle) and high surface quality, are presented in this work. Electropolishing based on forward pulse currents (PC) has been used to shape and polish Ni micro moulds that contain sets of micron-scaled linear ridges and star patterns in order to ease the separation of moulded polymeric parts from the metallic mould during ejection and demoulding. The use of forward pulsed currents improved the mould design by increasing the fillet radii and draft angle while keeping the surface roughness low and maintaining a good surface shine. An optimization study of forward PC using a green solution of nickel sulfamate varied EP times (0–70 min) and duty cycles (40, 50, 60, and 70%) at a process conditions of 2.8 V, 50 °C, and 250 rpm. The best topographical and morphological changes were observed for a typical microfluidic channel ( w × h , 100 × 110 μm) with an EP time of 70 min and 50% duty cycle: fillet radius increased by 3.8 μm, draft angle by 3.3°, and the channel width reduced by 11.4% while surface roughness changed by 8.6% and surface shine improved by 48.9%. Experimental validation was performed using hot embossing wherein the electropolished Ni mould replicated the micro channels and star patterns in PMMA chips with notably fewer burrs, material pile up, and no feature distortion. Moreover, there was a reduction in the side wall roughness of micro channels in PDMS casting with electropolished Ni mould by 16%. Hence, this work presents a significant scientific contribution to improving the efficiency of micro mould tools and reduces the defects caused by friction and adhesion in replicated polymeric parts.

Precision machining of microstructures on electroless-plated NiP surface for molding glass components

Fabrication of Microglass Lens Mould by Using Ultraprecision Microgrinding Process

A review of the techniques for the mold manufacturing of micro/nanostructures for precision glass molding

Effect of tool geometry and cutting parameters on surface quality and chip morphology of amorphous electroless nickel-phosphorus alloy in ultra-precision turning

Investigation on shape transferability in ultraprecision glass molding press for microgrooves

Precision glass molding of diffractive optical elements with high surface quality.

Molecular dynamics simulation of the nano-cutting mechanism of a high-phosphorus NiP coating

Studies on Protective Coatings for Molding Tools Applied in a Precision Glass Molding Process for a High Abbe Number Glass S-FPM3

A green and precision compound machining method for glass micro components – Ultrasonic assisted electrochemical discharge grinding with multi-hole tube electrode

Micro Array Hole Formation in Glass Using Electrochemical Discharge Machining

Magnetorheological finishing of electroless nickel-phosphorus-plated mold for ultraprecision injection molding

Optimization of forward pulsed currents for combining the precision shaping and polishing of nickel micro mould tools to reduce demoulding defects

Study on nano-graphitic carbon coating on Si mold insert for precision glass molding

Investigation on the optimal ultra-precision machining of nitriding mold steel by in-situ laser assisted diamond cutting

Annealed high-phosphorus electroless Ni–P coatings for producing molds for precision glass molding

Precision Polishing Techniques for Metal Molding Dies and Glass Forming Technology “Slumping Method”

A Study on the Material Removal Characteristics and Damage Mechanism of Lapping for Pressureless Sintered Silicon Carbide (SSiC) Microlens Cavity

Precision shaping of nickel micro-mould features via electropolishing: Characterisation of electrolytes from strong to weak acids

Study of Interfacial Adhesion and Re-Ir Alloy Coating in Chalcogenide Glass Molding.