Abstract:For conventional acoustic monopole sources in a logging-while-drilling (LWD) or wireline environment, shear slowness logs can be hard to obtain, particularly in slow formations where direct refracted shear-wave arrivals are often absent. For LWD dipole sources, formation flexural waves are often coupled with the lowest order of tool flexural waves, so the flexural mode does not approach shear wave slowness at low frequencies. A dispersion correction is required to extract shear slowness from LWD dipole data. Instead, a quadrupole firing, which generates screw waves, is considered the best LWD excitation mode for shear measurement. A fundamental feature of screw waves in an LWD environment is that their non-leaky cutoff frequency slowness is the formation shear slowness. However, slowness data near the cutoff frequency of LWD screw waves are often influenced by noise or the presence of other modes because of low excitation amplitude. To overcome these LWD data processing challenges, we propose a data-driven processing method that uses all useful dispersion responses of existing modes in the frequency domain. The process first generates a differential phase frequency-slowness coherence map and extracts the slowness dispersion vs. frequency. Then, it computes the slowness density log, referring to the intensity of the dispersion response along the slowness axis. Next, an edge-detection method is applied to capture the edge of the first peak associated with shear slowness on the slowness density map. To refine the shear slowness answer, this initial estimate of shear slowness serves as the input to another algorithm that minimizes the misfit between the screw slowness vector and a simplified screw dispersion model. The simplified screw dispersion model consists of a pre-computed base library of theoretical screw dispersion curves and two data-driven parameters. The two data-driven parameters are used by the measured data to stretch the base dispersion model in the frequency and slowness axes, respectively, to account for errors generated by alteration, anisotropy, or other parameters not included in the forward modeling. The method can also be applied to flexural waves, where the initial guess of shear slowness is picked from the slowness density map of flexural waves after dispersion-correction processing. This paper shows a case study of borehole flexural and screw waves processing in soft formations. A modified differential-phase frequency-semblance (MDPFS) approach is applied to extract the mode waves' full-frequency dispersion response from measured waveforms. The data-driven shear slowness processing is applied to the dispersion response. Both dipole flexural waves and quadrupole screw waves are processed. A combination of slowness density log from the flexural or screw wave slowness and the dispersion-corrected slowness is used as a QC metric of the final estimated shear. Results show that flexural and screw dispersions are well measured by the LWD sonic tool, even if the shear slowness is as large as 500 s/ft. Shear slowness extracted from flexural waves and screw waves match well with each other and with wireline shear slowness logs, demonstrating that the processing is reliable and robust.

Sensitivity analysis of S-waves and their velocity measurement in slow formations from monopole acoustic logging-while-drilling

Investigation of the high-frequency wavefield of an off-center monopole acoustic logging-while-drilling tool

Simulation of the Borehole Quasistatic Electric Field Excited by the Acoustic Wave During Logging While Drilling Due to Electrokinetic Effect

Analysis of the Acoustic Wavefields Excited by the Logging-While-Drilling (LWD) Tool

Experimental measurements of monopole inner/outer collar waves and estimation of P wave velocity in acoustic LWD

Investigation and Use of Surface-wave Characteristics for Near-surface Applications

APPLICATION OF LWD ACOUSTIC DISPERSIVE DATA PROCESSING FOR HIGH-QUALITY SHEAR SLOWNESS LOGS IN SLOW FORMATIONS

Acoustic fields for monopole logging while drilling with an eccentric collar

Experimental studies on the mechanism of seismoelectric logging while drilling with multipole source

Wavefield simulation and analysis with the finite-element method for acoustic logging while drilling in horizontal and deviated wells

Interface Detection of Near-Borehole Stratified Formation under Different Permeabilities Based on Seismoelectric Logs: A Finite-Difference Modeling

Analytical solutions for dispersions and waveforms of acoustic logging in a cased hole

Study on Shear Velocity Profile Inversion Using an Improved High Frequency Constrained Algorithm

Radial profiling of near-borehole formation velocities by a stepwise inversion of acoustic well logging data

Joint inversion of formation radial shear-velocity profiles by dipole acoustic logging while drilling

Modeling and Inversions of Acoustic Reflection Logging Imaging Using the Combined Monopole–dipole Measurement Mode

Single-well S-wave imaging using multicomponent dipole acoustic-log data

Sensitivities of Phase-Velocity Dispersion Curves of Surface Waves Due to High-Velocity-Layer and Low-Velocity-Layer Models

Detection performance of azimuthal electromagnetic logging while drilling tool in anisotropic media

Experimental Measurements of Seismoelectric Signals in Borehole Models

Numerical Study on the Characteristics of Multipole Acoustic Logging While Drilling in Cracked Porous Medium