Abstract:The progress of the Separated Function RFQ (SFRFQ) accelerator, which can raise the field gradient of acceleration while maintaining the transverse focusing power sufficient for high current beam, is presented. In order to demonstrate the feasibilities of the novel accelerator, a prototype cavity was designed and constructed. Correspondingly, a code SFRFQCODEV1.0 was developed specially for cavity design and beam dynamics simulation. The prototype cavity will be verified as a post-accelerator for ISR RFQ-1000 (Integral Split Ring RFQ) and accelerate O from 1MeV to 1.6MeV. To inject a higher current oxygen beam for the prototype cavity, the beam current of ISR RFQ-1000 was upgraded to 2mA. The status of high power and beam test preparation for the prototype cavity are presented in this paper. INTRODUCTION As a type of low energy high current linear accelerator RFQs serve well as the first accelerator in a chain of linear accelerators, providing the initial bunching and acceleration of beams. However, because an enhancement of accelerating field would result in considerable reduction of transverse focusing, as both of the field components is deeply correlated with each other. The drift tube structure has higher acceleration efficiency, which is why the idea of introducing accelerating gaps into RFQ is also attractive for some applications. For example, SP RFQ [1], RFD [2] as well as chain-like structure [3] which import the accelerating gaps into RFQ, were under investigation in Russia, USA and Japan. As the same reason, the Separated Function RFQ (SFRFQ) was proposed by the RFQ group of IHIP Institute of Heavy Ion Physics) at Peking university [4], based on the experience of ISR-RFQ 1000 [5,6]. Initial results of electro-magnetic calculation and dynamics proved the possibility and higher RF accelerating efficiency of SFRFQ structure [7]. In order to demonstrate the feasibilities of the SFRFQ structure, a prototype cavity was designed and constructed. Correspondingly, a code SFRFQCODEV1.0 [8] was developed specially for cavity design and beam dynamics simulation. The prototype cavity will be verified as a post-accelerator for ISR RFQ-1000 (Integral Split Ring RFQ) and accelerate O beam with ~mA peak current from 1MeV to 1.6MeV. The status of high power and beam test preparation for the prototype cavity are presented in this paper. SFRFQ STRUCTURE AND THE FIRST PROTOTYPE The electrodes of SFRFQ are shown in Fig. 1(a), where diaphragms are mounted onto the quadruple electrodes with no surface modulation. Then every cell consists of a gap and a small quadruple lens, the acceleration and focusing field will be decoupled. As the space inside quadruple is very limited, the sparking is a challenge for the SFRFQ structure. In order to decrease the maximum surface electric field and have enough transverse focusing, an asymmetric quadruple is adopted as Fig. 1(b) shows. (a) Photo of the SFRFQ structure (1,2,3&4 diaphragms, 5 RFQ electrode) (b) asymmetric quadruple (left for ay<ax ;right for ax<ay ) Figure 1: SFRFQ structure As SFRFQ is a hybrid structure of RFQ and DTL accelerator, a special code called SFRFQCODEV1.0 is developed for its beam dynamics design. In order to demonstrate the feasibilities of the accelerator, a prototype cavity with 14 gaps, which accelerates mA oxygen beam from 1MeV to 1.6 MeV, is designed. The evolution of synchronous phase is plotted in Fig. 2, it shows the four gaps at the entrance are used for beam ___________________________________________ *Work supported by NNSFC (10455001) x.yan@pku.edu.cn Proceedings of EPAC08, Genoa, Italy TUOBM02 04 Hadron Accelerators A08 Linear Accelerators

The Fast Linear Accelerator Modeling Engine for FRIB Online Model Service

Fast longitudinal beam dynamics optimization in x-ray FEL linear accelerators

Advances of the FRIB Project

Beam Simulation Studies of ECR Beam Extraction and Low Energy Beam Transport for FRIB.

Fringe field simulations of a non-scaling FFAG accelerator

Linear and nonlinear beam dynamics of vertical fixed-field accelerators

New Tasks and New Codes for RFQ Beam Simulation

Fast modeling of regenerative amplifier free-electron lasers

Full-Cycle Simulations of the Fermilab Booster

THE FRIB SC-LINAC: INSTALLATION AND PHASED COMMISSIONING*

Separated Function Rfq Beam Dynamics Design and Commissioning

Design and beam dynamics validation of a spiral FFAG accelerator for CSNS-II

From Compact Plasma Particle Sources to Advanced Accelerators with Modeling at Exascale

Technological developments and accelerator improvements for the FRIB beam power ramp-up

Real-time Beam Transport Simulator for Wide Energy-Spread Proton Beam Generated by Laser Acceleration

Linear IFMIF Prototype Accelerator (LIPAc) Radio Frequency Quadrupole's (RFQ) RF couplers enhancement towards CW operation at nominal voltage

An Integrated Multi-Physics Optimization Framework for Particle Accelerator Design

FERMI: Fusion Energy Reactor Models Integrator

The development of the Separated Function RFQ accelerator at Peking University

Fast Particle-in-Cell simulations-based method for the optimisation of a laser-plasma electron injector

A computer code for beam dynamics simulations in SFRFQ structure