Abstract:Rationale Stable K isotope geochemistry is becoming an important tool for various applications. Developments in analytical methods for K isotopes based on multicollector inductively coupled plasma mass spectrometry (MC-ICP-MS) without collision cell will bring research capability of K isotopes to many existing MC-ICP-MS labs. Methods Stable K isotopes were analyzed without applications of "cold plasma" and collision cell on a Nu 1700 Sapphire high-resolution multicollector inductively coupled plasma mass spectrometer. A conventional dry and hot plasma setting is used for analysis to maintain high K sensitivity and signal stability, and high mass resolution was applied to provide interference-free shoulders of K-39(+) for isotopic measurement of K-41/K-39 ratios. Ar-40(+) ion beam generated in ICP was neutralized in the ion guide rail for the Daly detector. Results Under such operating conditions, an external reproducibility of <+/- 0.1 parts per thousand (2 standard deviation) for K-41/K-39 is achieved for K solutions of 1 ppm or above. Tests were carried out to evaluate the influence of total K loading, K concentration and acid molarity mismatch, matrix effects, and Ar-40(+) and (ArH+)-Ar-40-H-1 tailing on K isotope analysis. We found that the accuracy of K isotope analysis can be compromised by concentration mismatch of sample and standard K, by 0.007 parts per thousand in delta K-41 per 1% mismatch of K content. By contrast, mismatch of HNO3 molarity or existence of HCl in HNO3 exerts negligible influences on the analytical precision and accuracy of K isotope analysis. Furthermore, K isotope analytical results remain accurate when Na/K, Mg/K, Ca/K, Rb/K, V/K, and Cr/K ratios are below 3%. Conclusions The high-precision K isotope analytical method reported here is robust for studies on K isotopic variations in geological, cosmochemical, and biological samples. The f(41)K values of six international geostandards measured using our method are consistent with data measured using different analytical methods from other laboratories.

Development of a low-level Ar-37 calibration standard

Measurement of 37Ar to support technology for On-site Inspection under the Comprehensive Nuclear-Test-Ban Treaty

37 Ar source on-demand production and deployment for low-energy nuclear recoil measurement in ReD liquid Argon TPC

Quantifying the Potential of Argon Detection Capabilities for Nuclear Explosion Monitoring

Will $^{37}$Ar emissions from light water power reactors become an obstacle to its use for nuclear explosion monitoring?

A Facility for Low-Radioactivity Underground Argon

Precision Measurement of the Specific Activity of $^{39}$Ar in Atmospheric Argon with the DEAP-3600 Detector

Alteration of Natural 37ar Activity Concentration in the Subsurface by Gas Transport and Water Infiltration

Evaluation of SNOLAB background mitigation procedures through the use of an ICP-MS based dust monitoring methodology

Development of a low background liquid scintillation counter for a shallow underground laboratory

Cosmogenic production of $^{39}$Ar and $^{37}$Ar in argon

Ar-39 Detection At The 10(-16) Isotopic Abundance Level With Atom Trap Trace Analysis

Modeling Noble Gas Transport and Detection for the Comprehensive Nuclear-Test-Ban Treaty

Ambient Dose and Dose Rate Measurement in SNOLAB Underground Laboratory at Sudbury, Ontario, Canada

Detection and analysis of xenon isotopes for the comprehensive nuclear-test-ban treaty international monitoring system

Measurement of the Argon Purity by ICP-MS and Results of the Analysis of the Gas Used for the MicroBooNE Experiment

Characterising the Radionuclide Fingerprint of an Advanced Gas-Cooled Nuclear Power Reactor

A New Method of Measuring 81kr and 85kr Abundances in Environmental Samples

A Rn-220 source for the calibration of low-background experiments

Full characterization and calibration of a transfer standard monitor for atmospheric radon measurements

Precise Measurement of 41 K/ 39 K Ratios by High-Resolution Multicollector Inductively Coupled Plasma Mass Spectrometry under a Dry and Hot Plasma Setting