Abstract:The flower‐like polyimide (PI) based on 3,3′,4,4′‐benzophenone tetracarboxylic dianhydride and benzidine was successfully obtained via solvothermal method. Using the flower‐like PI as organic fillers, the flower‐like PI/PI composites were fabricated by using 4,4′‐diaminodiphenyl ether and 1,2,4,5‐pyromellitic dianhydride as monomers through in situ polymerization and thermal imidization. The residual amino groups on the surface of flower‐like PI microparticles easily lead to the formation of chemical linkage between the flower‐like PI and PI matrix, which are benefit for tight interface and uniform dispersion. These experimental results showed that the broken elongation of the composites was significantly improved from 9.8% (pure PI) to 33.5% (PI‐4%), but the tensile strength and Young's modules were slightly sacrificed. The glass transition temperatures were mainly concentrated at around 352°C, while the 5% and 10% thermal decomposition temperature were slightly reduced. Furthermore, the light transmittance remarkably decreased from 75.9% (pure PI) to 4.3% (PI‐5%) at 550 nm. When the incorporation of flower‐like PI was 5%, an obvious increase of water uptake from 2.05% to 2.89% was noticed, and the water surface contact angle increased from 67.5° to 89.4°, indicating the increasing hydrophobicity. Additionally, with the increase of flower‐like PI fillers, the gas permeation flux of H2, CO2, O2, and N2 enhanced by more than two times, and the selectivities of O2/N2 and CO2/N2 increased first and then decreased. Therefore, the flower‐like PI microparticles will be promising functional fillers to improve the properties of polyimide materials.

Fabrication of Cross‐Linked Polyimide Hollow Microspheres With Lightweight, Thermal Resistance and Controllable Size

Scalable Fabrication of Lightweight, Heat‐resistant and Controllable Sizes Polyimide Hollow Microspheres

Fabrication of size-controllable hollow nano-spheres based on polyimides composites

A simple strategy to prepare functional PI microspheres by constructing coating on PAA microspheres followed thermal imidization reaction

Preparation and Properties of High-Temperature-Resistant, Lightweight, Flexible Polyimide Foams with Different Diamine Structures

Fabrication of Lightweight Polyimide Foams with Exceptional Mechanical and Thermal Properties

Modified hollow glass microsphere isocyanate-based polyimide foam composite with improved mechanical and thermal insulation properties

Low dielectric constant polyimide mixtures fabricated by polyimide matrix and polyimide microsphere fillers

Low dielectric polyimide microsphere/polyimide composite films based on porous polyimide microsphere

Scalable preparation of individual, uniform hyper-crosslinked polyimide hollow spheres through solid-state powder foaming: The power of network manipulation

Enhanced toughness and gas permeabilities of polyimide composites derived from polyimide matrix and flower‐like polyimide microparticles

Preparation and Characterization of Electrospun Polyimide Microfibrous Mats with High Whiteness and High Thermal Stability from Organo-soluble Polyimides Containing Rigid-rod Moieties

Fabrication and Characterization of a High-Strength Polyimide/Thermoplastic Polyurethane Composite Aerogel with Hydrophobicity and Low Thermal Conductivity

Polyimide Aerogels with Excellent Thermal Insulation, Hydrophobicity, Machinability, and Strength Evolution at Extreme Conditions

Mechanically strong, thermal-insulated, and ultralow dielectric polyimide aerogels with adjustable crosslinking methods

Preparation of polyimide aerogels by freeze‐extraction and chemical imidization for 3D printing

Preparation and Properties of Low Internal Stress Polyimide-b-Polysiloxane with a Hyperbranched Structure

Preparation and Properties of Electrospun Polyimide Ultrafine Fibrous Mats with Excellent Heat-fusibility Via Hot-press Procedure from Organo-soluble Polyimides Containing Phenolphthalein Units

Mechanical and thermal properties of porous polyimide monoliths crosslinked with aromatic and aliphatic triamines

Hierarchical Polyimide Microparticles with Controllable Morphology

Synthesis and properties of novel colorless and thermostable polyimides containing cross‐linkable bulky tetrafluorostyrol pendant group and organosoluble triphenylmethane backbone structure