Abstract:Proceedings of the Institution of Mechanical Engineers, Part C: Journal of Mechanical Engineering Science, Ahead of Print. The machinability of 2.5D C/SiC composites is severely limited by their inherent brittleness, inhomogeneity, and anisotropy. Conventional machining techniques are often associated with several drawbacks, including elevated costs, significant tool deterioration, and suboptimal efficiency. In contrast, short electric arc milling (SEAM) emerges as a promising innovation in the field of specialized machining, serving as a crucial technical approach for the effective processing of conductive materials that pose machining challenges. This work explores the surface quality law after short arc machining of 2.5D C/SiC composites under different process parameters and investigates etching damage incurred. To assess the influence of different parameters on the surface quality post-machining, two evaluation indices were established: surface roughness (Sa) and the thickness of the heat-affected layer (HAL). A one-factor test was set up to analyze the voltage and current waveforms, the electron microscopy images of the processed surface, Raman spectra, and the surface energy spectrum, using Sa, HAL, and the microscopic morphology as the detection indices. Moreover, the study demonstrates that the arc discharge energy and the discharge frequency exert considerable influences on the quality of the machined surface. Both the Sa and HAL values increase with higher voltage and duty cycle, while they decrease with rising frequency and electrode rotation speed. Consequently, the surface quality can be enhanced by lowering the voltage and duty cycle and by increasing the frequency and electrode rotation speed. Notably, short arc machining leads to a high-temperature oxidation reaction, primarily producing SiO2, which serves to prevent further oxidation of the material. However, the process also results in microscopic defects, such as fiber breakage and fiber pull-out. These findings offer both theoretical and experimental foundations for the future realization of high-efficiency and high-quality processing of 2.5D C/SiC composites via SEAM.

Study of atomized discharge ablation-chemical composite machining of SiCp/Al

Processing of silicon carbide particulate reinforced aluminum alloy composites using rotary electrochemical discharge machining

Study of ablation behavior on 2.5-dimensional C/SiC composites processed via short electric arc milling with various parameters

Effect of short electric arc milling discharge machining on the processing performance of two-dimensional C/SiC composites

Study of the High-Efficiency Ejecting-Explosion EDM of SiCp/Al Composite

Study on productivity and aerosol emissions of magnetic field-assisted EDM process of SiC p / Al composite with high volume fractions

Research on ultrasonic vibration–assisted electrical discharge machining SiCp/Al composite

Analysis and Optimization of the Machining Characteristics of High-Volume Content SiCp/Al Composite in Wire Electrical Discharge Machining

Investigation of the Thermophysical Simulation and Material Removal Mechanism of the High-Volume-Fraction SiCp/Al Composite in Wire Electrical Discharge Machining

Effect of atomization amounts on electrical discharge ablation machining and electrochemical machining

Experimental investigations on silicon carbide mixed electric discharge machining

Investigation on Electrochemical Jet Machining of High Volume Fraction SiCp/Al Composite

An Experimental Study on Rotary Ultrasonic Machining of High Volume Fraction Silicon Carbide-reinforced Aluminum Matrix Composites (Sicp/al)

A hybrid short electric arc and electrochemical machining of the Ti6Al4V alloy

Micro Electrical Discharge Machining of Ultrafine Particle Type Tungsten Carbide Using Dielectrics Mixed with Various Powders

High efficiency blasting erosion arc machining of 50 vol.% SiC/Al matrix composites

A review on conventional and nonconventional machining of SiC particle-reinforced aluminium matrix composites

Sustainable electric discharge machining using alumina-mixed deionized water as dielectric: Process modelling by artificial neural networks underpinning net-zero from industry

Finite Element and Experimental Analysis of Ultrasonic Vibration Milling of High-Volume Fraction SiCp/Al Composites

Experimental optimization of machining GH4145 by atomizing discharge ablation milling

Surface Modification Using Assisting Electrodes in Wire Electrical Discharge Machining for Silicon Wafer Preparation