Abstract:We present two prototypes of a gigabit transceiver ASIC, GBCR1 and GBCR2, both designed in a 65-nm CMOS technology for the ATLAS Inner Tracker Pixel Detector readout upgrade. The first prototype, GBCR1, has four upstream receiver channels and one downstream transmitter channel with pre-emphasis. Each upstream channel receives the data at 5.12 Gbps through a 5 meter AWG34 Twinax cable from an ASIC driver located on the pixel module and restores the signal from the high frequency loss due to the low mass cable. The signal is retimed by a recovered clock before it is sent to the optical transmitter VTRx+. The downstream driver is designed to transmit the 2.56 Gbps signal from lpGBT to the electronics on the pixel module over the same cable. The peak-peak jitter (throughout the paper jitter is always peak-peak unless specified) of the restored signal is 35.4 ps at the output of GBCR1, and 138 ps for the downstream channel at the cable ends. GBCR1 consumes 318 mW and is tested. The second prototype, GBCR2, has seven upstream channels and two downstream channels. Each upstream channel works at 1.28 Gbps to recover the data directly from the RD53B ASIC through a 1 meter custom FLEX cable followed by a 6 meter AWG34 Twinax cable. The equalized signal of each upstream channel is retimed by an input 1.28 GHz phase programmable clock. Compared with the signal at the FLEX input, the additional jitter of the equalized signal is about 80 ps when the retiming logic is o . When the retiming logic is on, the jitter is 50 ps at GBCR2 output, assuming the 1.28 GHz retiming clock is from lpGBT. The downstream is designed to transmit the 160 Mbps signal from lpGBT through the same cable connection to RD53B and the jitter is about 157 ps at the cable ends. GBCR2 consumes about 150 mW when the retiming logic is on. This design was submitted in November 2019.

Gbit/s Data Transmission on Carbon Fibres

60 Gbit/s 400 GHz Wireless Transmission

High-Speed Transmission Cable Performance- Simulations and Measurements

107.1-Gbps net-rate transmission over a joint 51km-fibre-and-10.7m-wireless link for terahertz radio access networks

17 Gb/in/sup 2/ Areal Density Demonstration at 214 Mb/s

Gbps Impulse Radio ( IR ) Ultra-Wideband ( UWB ) Transmission over 100 Meters Multi Mode Fiber with 4 Meters Wireless Transmission

100-Gbps Hybrid Optical Fiber-Wireless Transmission

Lightweight, Flexible, High-Performance Carbon Nanotube Cables Made by Scalable Flow Coating

First Demonstration of Field-Deployable Low Latency Hollow-core Cable Capable of Supporting >1000km, 400Gb/s WDM Transmission

High-Ampacity Power Cables of Tightly-Packed and Aligned Carbon Nanotubes

Practical Solutions for 400 Gbit/s Data Center Transmission

Flexible bandwidth 448 Gb/s DMT Transmission for Next Generation Data Center Inter-Connects

Test bench of a 100 Gbps radiation hardened link for future particle accelerators

Field Transmission of 100 G and Beyond: Multiple Baud Rates and Mixed Line Rates Using Nyquist-WDM Technology

Field Trial for the Mixed Bit Rate at 100G and Beyond

Low-Latency and High-Speed Hollow-Core Fiber Optical Interconnection at 2-Micron Waveband

Faster Than Fiber: Demonstration of over 100 Gb/s Signal Delivery at W-band

Towards high-capacity fibre-optic communications at the speed of light in vacuum

High-Throughput and Long-Distance Transmission With >120 nm S-, C- and L-Band Signal in a 125μm 4-Core Fiber

1.28 and 5.12 Gbps multi-channel twinax cable receiver ASICs for the ATLAS Inner Tracker Pixel Detector Upgrade

Record 202.3 Tb/s Transmission over Field-Deployed Fibre using 15.6 THz S+C+L-Bands